crazyazsredneck
New member
- 4
- 0
- 0
- Location
- ridgeland ms,
hi yall just got a mule ,it has a 4 cylinder willys. i put new magneto in but i sure its out of time . any body know how to time it. thanks for any help
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
m274 needs timing
- Thread starter crazyazsredneck
- Start date
clinto
Moderator, wonderful human being & practicing Deuc
Staff member
Administrator
Super Moderator
Steel Soldiers Supporter
Supporting Vendor
- 12,596
- 1,132
- 113
- Location
- Athens, Ga.
This is probably for the 2 cyl engine only, but it's the best I can do.
Motor Pool
There is a guy here who has a 4 cylinder Mule and is pretty knowledgable but he doesn't post much.
Motor Pool
There is a guy here who has a 4 cylinder Mule and is pretty knowledgable but he doesn't post much.
crazyazsredneck
New member
- 4
- 0
- 0
- Location
- ridgeland ms,
yes thats a 2 cylinder. mr watson has that on his site. gonna call him monday
thanks
thanks
TKRESS1
Member
- 86
- 3
- 8
- Location
- HANOVER PA
Need help
Looking for tips on timing the 4cyl motor. We have it close but can not get it right. Let me know if anyone can help.
Looking for tips on timing the 4cyl motor. We have it close but can not get it right. Let me know if anyone can help.
clinto
Moderator, wonderful human being & practicing Deuc
Staff member
Administrator
Super Moderator
Steel Soldiers Supporter
Supporting Vendor
- 12,596
- 1,132
- 113
- Location
- Athens, Ga.
Austringer is probably the undisputed expert in the 4 cyl realm. Hopefully he'll chime in within a few days.
natem
Member
- 692
- 17
- 18
- Location
- freeland/michigan
If you have the correct TM study the photos, the text is misleading. Your best bet is to use a vacuum gauge. I don't know if a standard timing light will work with a magneto.
major519
Member
- 52
- 8
- 8
- Location
- Nipissing, Ontario, CA
Standard timing light will work but you need to make or purchase an adapter.
Adapters are not hard to make from an old spark plug wire or you can buy one from a parts supplier.
Adapters are not hard to make from an old spark plug wire or you can buy one from a parts supplier.
crorlo
New member
- 8
- 0
- 0
- Location
- Houston, Texas
Can it be done?
Can you install the magneto in a two cycle engine without taking the governor off to align the V marks, as long as the impulse coupling clicks between 18 and 28?
Can you install the magneto in a two cycle engine without taking the governor off to align the V marks, as long as the impulse coupling clicks between 18 and 28?
- 26,246
- 1,179
- 113
- Location
- NY
Did you mean two cylinder? Did you pull your mag, but not your governor and now you need to re-install it?
The answer would be yes, but you need the gear installed from the governor side(and to see the marks), so if your gear is installed, you simply have 2 choices to install the mag based on the pin drive holes.
The governor can be removed in about 3-4 minutes.
To do it correctly takes about 7-10 min.
TKRESS1
Member
- 86
- 3
- 8
- Location
- HANOVER PA
Got it
We got my 4 cyc engine running smooth. Just need a little clean-up and we will be ready to install. Thanks for all the help.
We got my 4 cyc engine running smooth. Just need a little clean-up and we will be ready to install. Thanks for all the help.