Two Stroke Madness
Member
- 195
- 4
- 18
- Location
- Adams NY
That is odd. What brand of oil filter are you running?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M939 Oil Change, Best Oil, Tips and Tricks
- Thread starter 99nouns
- Start date
Rule of thumb on any military truck. Never trust your gauges. If you think its suspicious take 5 mins and screw a pressure tester into it and vary them against the readings. You can also solder a ground wire directly to the sending unit and establish a good frame ground. Also try to clean the port on the bottom of the unit. May have gunk. Add stabilent 22 to the connection point.
Sent from my SM-G860P using Tapatalk
Sent from my SM-G860P using Tapatalk
I replaced it with the original one from ebay had a good deal.
If I only had a pressure tester!!! What does it mean to have a high pressure in acceleration, is it clogged somewhere? I know the gauge was stuttering before but it never went high like that before. Should I look for any symptoms? I need to run down to auto store and see if they have a pressure tester for loaners.
They will loan you one. Gauges are always iffy. Sure way is to swap it all to a manual gauge for about 75$ ;
Sent from my SM-G860P using Tapatalk
mcmullag
Member
- 919
- 13
- 18
- Location
- Colorado Springs, CO region
I ran shell rotella 15w-40 in mine, have owned 2 of them, and added some Lucas for the heck of it. Mine were only used for parades and shows, really babied them.
- 737
- 14
- 18
- Location
- Bothell, WA
What mechanical gauge did you go with?
- 3,224
- 398
- 83
- Location
- Tonopah, AZ
I had a erratic oil gauge and it trued out to be the wire coming from the sending unit to the gauge. I just replaced that wire and all good now.
I got this from NAPA
https://www.napaonline.com/en/p/BK_5011731
It came with everything, the ports, adapters, tubing. I couldn't afford $70 original gauge at the moment, if took me 5 mins to install, only issue is no light because of it doesnt have clear housing to work with truck's internal lighting, it does look like a new guy in old school among all the other gauges but it is my project truck so I might think of something else later. It works right now and that's what matters.
I dont know how did you figure to replace the wire, that wire twist around and travels to more places than New York City Subway.
Leave the old wire in its place and simply just run a new one thru the firewall hole up and over the steering column and into the dash
Sent from my SM-G935P using Tapatalk
- 3,224
- 398
- 83
- Location
- Tonopah, AZ
99nouns Yes just run a new wire and route it the best way you can. I think there is a pass though on the fire wall close to the black box.
That is were I run into the cab.
That is were I run into the cab.
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Yes leaving the bad/defective wire in place and adding the new one is very common in the marine industry. It is called "abandon in place". Usually much quicker than pulling old cable and time is money.
Just an update as I have always ran Rotella 1540 just basic stuff. I ran the T6 synthetic for a bit and my engine didn't like it. She got loud. No surprise.
I just did a recent oil change and went over to Delo 400 SDE cause it was on sale for $10 a Costco. I know this stuff is fairly new only being out about a yeaer. Some say not for older engines, some say it is fine. I am going to do a 3000mi oil analysis and go from there, I also have a bypass filter that adds additives back into the system but I guess ill have to check that opinion out later with my own lab results. I was running standard rotella 15 to 18k with the bypass unit. I wasn't testing it though.
I just did a recent oil change and went over to Delo 400 SDE cause it was on sale for $10 a Costco. I know this stuff is fairly new only being out about a yeaer. Some say not for older engines, some say it is fine. I am going to do a 3000mi oil analysis and go from there, I also have a bypass filter that adds additives back into the system but I guess ill have to check that opinion out later with my own lab results. I was running standard rotella 15 to 18k with the bypass unit. I wasn't testing it though.
rickyrecon
New member
- 8
- 0
- 1
- Location
- Forest/VA
I know this is an older post - but I am having a terrible time keeping my oil filter assembly from leaking. Any advice is appreciated. I have an M939 and just replaced the canister filter and gasket. I feel dumb - that I can't figure this out. I put the gasket around the head assembly then tighten the canister 'pretty tight' yet I still get a small stream. ... maybe I'm over tightening and causing the gasket to spill out? It seems a larger gasket would cause a better fit. Any advice is appreciated. Thank you, Rich
I hope Wes is around to say something!
- 6,092
- 4,499
- 113
Convert to spin on and call it done. I think floridianson had a spin on conversion for sale reasonably.
- 5,638
- 2,957
- 113
- Location
- Metairie/La (N'awlins)
I 2nd that. Fleetguard sells the conversion plate. Change to a modern spin on filter and there are many choices for filter such as extended capacity and life etc.
Canister technology is way old school and much better choices now.
Not that expensive. Use a baldwin or fleetguard. Baldwin OB-1368
I recall others having issue with wix/napa.
Canister technology is way old school and much better choices now.
Not that expensive. Use a baldwin or fleetguard. Baldwin OB-1368
I recall others having issue with wix/napa.
- 3,224
- 398
- 83
- Location
- Tonopah, AZ
Yes I also did all my trucks over to spin on's.