Good genes…
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Mav’s M1088A1 Conversion
- Thread starter Mavcaster
- Start date
- 16,941
- 24,629
- 113
- Location
- Burgkunstadt, Germany
Ah! Now Chucky has a lawyer!
I bought 1 of @gimpyrobb new intake cans with filters in it and dropped my filter price from 200 to 35 bucks for filter replacement and check out my exaust relocation will give you alot more useable clean frame rail to mount stuff on and just loosen the last band clamp on tailpipe and cut the last 2 feet of tail pipe off and spin the remaining short S piece to flush with frame rail or straight down towards the ground i just used some square tube tucked up in the bed frame with flex pipe tieing them together check out post 11 and 447 on my thread for pics of intake and exaust
Last edited:
- 16,941
- 24,629
- 113
- Location
- Burgkunstadt, Germany
So where are the pictures? Or is your seeing eye dog on vacation?
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 758
- 113
- Location
- Cincy Ohio
I still have a good amount of those Donaldson housings with filters. I just bought a house AND we're headed to haspin rally this weekend.
If you want one, shoot me a pm and gimme a bump on wed.
If you want one, shoot me a pm and gimme a bump on wed.
Idont know how to move pics from my thread to this one ! Might still be in my phone but i got shat to do now will post later ! OMG it just dawned on me u want more pictures of lula bell your sex slave ! You should be ashamed !
Thank you but I think I’m going to go with the Donaldson P/N D100031 filter housings on mine but man are they expensive! You don’t happen to have any of those do you? What’s the diameter of the one @chucky has? My main goal is space saving for these so if they’re comparable and I can run only 1 filter that would be nice.
- 16,941
- 24,629
- 113
- Location
- Burgkunstadt, Germany
Not bad Chucky. Maybe you need to think about a new day job.
coachgeo
Well-known member
- 5,150
- 3,466
- 113
- Location
- North of Cincy OH
I resemble that remark.
Been there bent that... (often)
You should look real close since your where your at to see if you have any oil leaks around the aftercooler that the oil filter base is bolted to if not carry on ! Oh and Ace hardware has its own brand of spray paint in CAT yellow that looks gooooooood ! Oh and i dont see any braceing under that cab you might not be as lucky as me if it falls down on you ! Put something stout under there just in case !Surprisingly enough all of these manifold bolts came out no problem. I was sure one was going to snap on me just because that’s my luck.
How well does regular enamel hold up to the heat though? I just coated the exhaust manifold with some VHT header paint which I know won’t even really last all that long.
And thanks for looking out, the truck is actually parked with nose slightly downhill so I’m not worried about the cab. I usually do throw a 4x4 post in there though when I’m just doing normal mx.
And thanks for looking out, the truck is actually parked with nose slightly downhill so I’m not worried about the cab. I usually do throw a 4x4 post in there though when I’m just doing normal mx.
- 705
- 1,804
- 93
- Location
- San Diego, CA
Hey thanks, I was trying to find the dude who installed an electric hydro pump and this is him so thank you for that. Also interested in that little dryer as well so searching for some more details on it. Not really a fan of the the tank setup but definitely some good ideas throughout.
EDIT: I found the dryer but it’s 12v. Still brings up a good thought on replacing the OE dryer while I’m in the process of relocating. Gonna keep digging.
Last edited:
