• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

MEP-002A, will Start, Run then dies....any suggestions?

1FAST4

1FAST4

Member
41
21
8
Location
NorCal
I have a MEP-002A that is our Backup Whole-House power souce. It last ran with a load on it about 6 months ago during a power outage. At that time, it ran for about 9 hours without issue. I normanly fire it up every other month just to keep the batteries topped off (also has a NOCO maintainer attached) but haven't had time due to work and an ill Mom.

Today, went to fire it up and it was a little slow to start but it did. after running for about 1 min, it died. Re-started multiple times and it would only run for 15 to 20 Seconds then die; as it started lossing RPM to die it would start sending gray smoke out of the exhust pipe.

Fuel pump clicking alone.
Fuel is good.
Fuel Filters "Spin on kit" only 3 hrs on them.

Any help with troubleshooting would be greatly appreciated.
 
Scoobyshep

Scoobyshep

Well-known member
1,134
1,508
113
Location
Florida
1FAST4 said:
I have a MEP-002A that is our Backup Whole-House power souce. It last ran with a load on it about 6 months ago during a power outage. At that time, it ran for about 9 hours without issue. I normanly fire it up every other month just to keep the batteries topped off (also has a NOCO maintainer attached) but haven't had time due to work and an ill Mom.

Today, went to fire it up and it was a little slow to start but it did. after running for about 1 min, it died. Re-started multiple times and it would only run for 15 to 20 Seconds then die; as it started lossing RPM to die it would start sending gray smoke out of the exhust pipe.

Fuel pump clicking alone.
Fuel is good.
Fuel Filters "Spin on kit" only 3 hrs on them.

Any help with troubleshooting would be greatly appreciated.
Click to expand...
Can you send a video?

do you have both pumps clicking?

Do you run any fuel additives?


my gut feeling is something has gotten gummed up.
 
1FAST4

1FAST4

Member
41
21
8
Location
NorCal
Scoobyshep said:
Can you send a video?

do you have both pumps clicking?

Do you run any fuel additives?


my gut feeling is something has gotten gummed up.
Click to expand...
Video; I have one but can't figure out how to upload it to the site...says the file extention (..,mp4) is not supported.
Both pumps are clicking.
Yes on additives. I use Pri-D, Stanadyne, Bio Kleen on all stored (little use) Diesel Fuel.
 

Attachments

Guyfang

Guyfang

Moderator
Staff member
Moderator
16,755
24,064
113
Location
Burgkunstadt, Germany
Chainbreaker said:
Agree, very common for OPS to fail over time. Try jumping across the OPS pins & see if it then runs. If it does "Run Jumper'd" make sure that Oil Pressure comes up above 40 PSI, if it doesn't turn it off so you don't risk any damage to engine.
Click to expand...
Put a jumper wire in at TB5-8 to TB5-9. Try and start it up. What happens.
1731947974720.png
 
Scoobyshep

Scoobyshep

Well-known member
1,134
1,508
113
Location
Florida
1FAST4 said:
Video; I have one but can't figure out how to upload it to the site...says the file extention (..,mp4) is not supported.
Both pumps are clicking.
Yes on additives. I use Pri-D, Stanadyne, Bio Kleen on all stored (little use) Diesel Fuel.
Click to expand...
Not sure if i missed it, but i dont see a lubrication additive.
 
1FAST4

1FAST4

Member
41
21
8
Location
NorCal
Chainbreaker said:
Agree, very common for OPS to fail over time. Try jumping across the OPS pins & see if it then runs. If it does "Run Jumper'd" make sure that Oil Pressure comes up above 40 PSI, if it doesn't turn it off so you don't risk any damage to engine.
Click to expand...
Chainbreaker,
The TM says to check continuity across the two terminals and if there is continuity replace OPS....to me that seems the OPS would be Normaly Open (NO) when not running....wouldn't jumping it just create continuity?

Also, when it was running yesterday (for 15-30 seconds) the Oil Pressure did come up to at or above 40 PSi according to the gauge.
 
Scoobyshep

Scoobyshep

Well-known member
1,134
1,508
113
Location
Florida
1FAST4 said:
Chainbreaker,
The TM says to check continuity across the two terminals and if there is continuity replace OPS....to me that seems the OPS would be Normaly Open (NO) when not running....wouldn't jumping it just create continuity?

Also, when it was running yesterday (for 15-30 seconds) the Oil Pressure did come up to at or above 40 PSi according to the gauge.
Click to expand...
its normally open and pressure closes it, the TM is testing a failed closed situation, your possible failure is a failing open. Jumping it takes it out of the equation.
 
Mullaney

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,716
19,766
113
Location
Charlotte NC
1FAST4 said:
Video; I have one but can't figure out how to upload it to the site...says the file extention (..,mp4) is not supported.
Both pumps are clicking.
Yes on additives. I use Pri-D, Stanadyne, Bio Kleen on all stored (little use) Diesel Fuel.
Click to expand...
.
Yes sir... Sad to say we don't host video files here. Gotta upload your video to YouTube (or equivalent), then copy a link to the site.
 
C

Chainbreaker

Well-known member
1,796
1,992
113
Location
Oregon
1FAST4 said:
Does this look like the correct OPS? Figured I'd try to find one, or two just in case. It's a Hobbs M4008-15 NOS
Click to expand...
The part looks the same (physical case) however it needs to be the right PSI... many times they "look the same" but are not the right PSI trip point.

This is the correct OP Switch as listed in the -24P parts manual

47 15 PAOZZPAOZZPAHZZ 5930-01-039-3140 SWITCH, PRESSURE EA 1 1 M-1423-14 74400 309-0177 44940
 
C

Chainbreaker

Well-known member
1,796
1,992
113
Location
Oregon
Scoobyshep said:
yep If it still fails then theres another issue.
Click to expand...
That's why GuyFang listed the procedure to test both the "Temp Switch and the Oil Pressure switch" in Post #7 above. Though in my experience and other reports, 99% of the time it's the "Oil Pressure Switch" as the Temp Switch usually doesn't fail, it can though if broken terminal or wire going to it loses continuity... but rare!
 
Guyfang

Guyfang

Moderator
Staff member
Moderator
16,755
24,064
113
Location
Burgkunstadt, Germany
You wrote:
Does this look like the correct OPS? Figured I'd try to find one, or two just in case. It's a Hobbs M4008-15 NOS


No. This not the correct switch. First find out if you need the switch. You are getting the cart in front of the horse. Proper troubleshooting saves time and money.

Below is a link to TM's. Yes, I know its for the MEP-003A, the 10 KW. Doesn't matter. They are more up to date than the 002A Books.

All the TM's you need to work on the MEP-003A

All the TM's you need to work on the MEP-003A
www.steelsoldiers.com
 
You must log in or register to reply here.
110,879members
165,309threads
2,326,154posts
1,392online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks