FYI for future reference that fuse mod doesn't have to be a high dollar slo blow type. I stuck an automotive type fuse holder on mine with a fast acting glass fuse. It hasn't blown in over 100 hours use. Plus I have the piece of mind knowing if I have a problem it should blow quickly. Not as sexy looking but functional.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
MEP 803a with Mil Trailer
- Thread starter m561gamagoat
- Start date
m561gamagoat
Active member
- 146
- 30
- 28
- Location
- Akron/Ohio
I bought a 5 pack of fuses. Was like $18.00 so no biggie. Relatively cheap overall. I spend more on lunch every week! Lol.
m561gamagoat
Active member
- 146
- 30
- 28
- Location
- Akron/Ohio
I get it. Guess i’m just gettin lazy and spoiled by Amazon! Lol
m561gamagoat
Active member
- 146
- 30
- 28
- Location
- Akron/Ohio
Quad Mod
Did this today. Seemed pretty straightforward!
Did this today. Seemed pretty straightforward!
Attachments
m561gamagoat
Active member
- 146
- 30
- 28
- Location
- Akron/Ohio
Ok, after installing the quad MOV mod I noticed the unit is charging at a higher percentage in the green. Before it was just into the green now its well into the green. Did this Mod cause that ?
- 2,168
- 3,610
- 113
- Location
- Pepperell, Massachusetts
The MOV would have no impact on the battery charging rate.
After each start it's normal to have it up in the green and then slowly drop back to near zero after the set has run and the batteries get recharged after being drawn down some by starting the set.
After each start it's normal to have it up in the green and then slowly drop back to near zero after the set has run and the batteries get recharged after being drawn down some by starting the set.
- 1,052
- 1,521
- 113
- Location
- Wilson County, Texas
If you're worried about the charge rate on the batteries, check the voltages on them. If the batteries are on their way out, the alternator will work harder to bring them up to where they want to be.
Great deal! I'd love to get the bigger MEP 803A for my house. Waiting for a good deal to pop up like that close to me.
Good job getting that MOV & Quad mod taken care of. Easy & gives a piece of mind.
Trailer is very easy to change over to 12v so it will plug into your truck. I modified mine to pull level & with lights. I made a thread on it here.
If you haven't already, give the unit a good load test. That will bring up any problems that may be there.
Great deal! I'd love to get the bigger MEP 803A for my house. Waiting for a good deal to pop up like that close to me.
Good job getting that MOV & Quad mod taken care of. Easy & gives a piece of mind.
Trailer is very easy to change over to 12v so it will plug into your truck. I modified mine to pull level & with lights. I made a thread on it here.
If you haven't already, give the unit a good load test. That will bring up any problems that may be there.
FloridaAKM
Well-known member
- 2,699
- 392
- 83
- Location
- Gainesville, Florida
I tried to get a late model M-803A, but it went for $4250.00 plus fees for a non runner, which is not a smart move for me. Maybe better luck next time!
NATCAD
Active member
- 241
- 50
- 28
- Location
- Port Huron Michigan
What were the part numbers and where did you source the mod parts from?
- 2,168
- 3,610
- 113
- Location
- Pepperell, Massachusetts
Last few fuse holders and fuses I bought off of eBay.
If you need a MOV or two I can mail you them. No charge.
If you need a MOV or two I can mail you them. No charge.
- 3,860
- 6,074
- 113
- Location
- MA
Here is where I got my last batch from
www.allfuses.com
www.allfuses.com
Seem to work just fine
FNQ-R-3
FNQ-R 3 Amp, 600V, Class CC, Bussmann FNQ-R-3, FNQ-R 3A | aka: Limitron FNQ-R-3, Cooper Bussmann FNQ-R-3, UPC: 051712147088
www.allfuses.com
30311R
30311R, 600V, Fuse Block, Ferraz 30311R | aka: Mersen 30311R, Ferraz Shawmut 30311R, UPC: 782001758394
www.allfuses.com
Seem to work just fine