- 2,733
- 863
- 113
- Location
- Oakwood, Ga
Damn timing in life sometimes sucks! That guy got a deal.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
MRAP wheels not fitting up front
- Thread starter Hummer Guy
- Start date
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
Smart I'm going to give that a try, I found some 1/2 Inch adapters, if those give it enough space than I'll go for some spacers in between the adapters. Does anyone have a picture of how close the tie rods are to the stock wheels or how it is to the other MRAP wheels?
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
After getting the wheel out of the way and checking under the truck, the wheel is rubbing on the arm that connects to the tie rod. My adapter plate is 3/8 in thick. Im guessing the 1/2-inch-thick spacer should solve the problem or at least I hope. These wheels offset seems very similar to the stock wheels
- 6,995
- 2,567
- 113
- Location
- Montevideo/Uruguay
There's only about ½" left in between arm and wheel.
And for comparison: stock M35 wheels have ~10.5" backspace.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
Perfect, this spacer should work.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
Is it safe to drive with the NDTs tires on the front temporarily? I have to move some stuff for about 20 miles. (Only around 800Ibs)
- 6,089
- 4,493
- 113
Do you have an air shift tcase or sprag?
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
air shift
- 807
- 832
- 93
- Location
- W.WA
That's the funny thing with selling military wheels/tires. No one wants them until you finally mark them down to just get rid of them and all of a sudden more people need them.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
After taking some measurements, I highly doubt the spacer would work, the wheels I have is about 2 1/2 inch deeper inside than the stock wheels. What do you guys think about running the stock wheels on the 395s? I know people do it, but I'm concern about the rubbing since I have the waterloo power steering kit.
- 6,089
- 4,493
- 113
Stock wheels and 395s are a bad idea.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
- 6,089
- 4,493
- 113
The path of least trouble and least complexity is to get the aluminum MRAP rims that are shown on my deuce in the picture.
I had no issues with them, but my steering was stock. I'm not sure if there's an issue with your aftermarket steering.
I had no issues with them, but my steering was stock. I'm not sure if there's an issue with your aftermarket steering.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
20" X 10" 335MM 10-Lug Hutchinson Aluminum Military MRAP 4X4 6X6 CTIS Wheel Rim (dvresidency.shop) Maybe Im wrong, but this seems way too good to be true
- 6,089
- 4,493
- 113
Those work. Not my first choice as they leave the fragile valve stem rather exposed. I've broken more than one valvestem on those...
But they're priced right, and a pronounced improvement from what you've got now.
Hummer Guy
Well-known member
- 843
- 807
- 93
- Location
- United States Louisiana
Interesting, Im going to just wait and see if I could find the other aluminum ones, I'll just look like a tractor with small tires in the front and big tires in the rear for now if I have to use the truck lol