MrArmyAnt
New member
- 90
- 0
- 0
- Location
- Dallas, TX
I bought a frame and a GMA soft top. What the **** is the order of operations on putting it on.
Last edited:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
N00b Question on Soft Tops
- Thread starter MrArmyAnt
- Start date
steelandcanvas
Well-known member
- 6,187
- 85
- 48
- Location
- Southwestern Idaho
Install the frame. Toss the soft top on the hood, upside down. Thread the windshield piping through the rolled sheet metal on top of the windshield. Flip top over, pull onto cab tub, tie down.
Last edited:
txdodge43man
New member
- 568
- 4
- 0
- Location
- Magnolia, texas
MrArmyAnt
New member
- 90
- 0
- 0
- Location
- Dallas, TX
I figured it out just before ya posted that. That was a very tight, unlubed fit. I don't have the three bows that go in the center 
I was going to look for new weather stripping for everything but I still don't think it would cover all the gaps. I'm thinking a visit to Mcmaster Carr's site and getting some over kill ones with sheet metal screws may be the ticket.
I was going to look for new weather stripping for everything but I still don't think it would cover all the gaps. I'm thinking a visit to Mcmaster Carr's site and getting some over kill ones with sheet metal screws may be the ticket.
wreckerman893
Possum Connoisseur
- 15,629
- 2,054
- 113
- Location
- Akenback acres near Gadsden, AL
1. Take soft top and place on pile of flammable material.
2. Using a powerful accelerant set pile on fire.
3. Dance around fire while howling at the moon.
4. Install hard top.
Worked for me.
2. Using a powerful accelerant set pile on fire.
3. Dance around fire while howling at the moon.
4. Install hard top.
Worked for me.
ODdave
New member
- 3,213
- 41
- 0
- Location
- lansing michigan
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
Last edited:
Westech
CPL
- 6,104
- 208
- 63
- Location
- cow farts, Wisconsin
This one time...... ah forget it
Motorcar
Member
- 271
- 3
- 18
- Location
- San Antonio, TX
Erik's has the twist tabs that go over the door window rail if yours are missing, the three rods are easy to make with some stock bar steel from Lowe's and a hammer/vice.
CobraCDR
New member
- 316
- 2
- 0
- Location
- Twin Cities, MN
You can post them anytime now that you have it on!
- 14,261
- 1,759
- 113
- Location
- Dayton, OH
So that's what I've been doing wrong. I've been attaching the top and then trying to put the frame and bows inside it...........
saddamsnightmare
Well-known member
- 3,618
- 80
- 48
- Location
- Abilene, Texas
October 27th, 2011.
My M35A2 came with the hard top. It's too darn hot in the summer and too darn cold in the winter. Replaced same with GMA insulated soft top and a bow set acquired from the folks in Utah...no complaints! a much better top for me and easier to remove when the need occurs!
My M35A2 came with the hard top. It's too darn hot in the summer and too darn cold in the winter. Replaced same with GMA insulated soft top and a bow set acquired from the folks in Utah...no complaints! a much better top for me and easier to remove when the need occurs!
MrArmyAnt
New member
- 90
- 0
- 0
- Location
- Dallas, TX
Here she is. Still needs to be painted, wheel cylinder replaced, and bed stained.
Attachments
ODdave
New member
- 3,213
- 41
- 0
- Location
- lansing michigan
What skins are on it? 48's?
steelandcanvas
Well-known member
- 6,187
- 85
- 48
- Location
- Southwestern Idaho
Man, I sure am glad you put that winky thing at the end of you post.So that's what I've been doing wrong. I've been attaching the top and then trying to put the frame and bows inside it...........