-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
No longer broke down in Flagstaff AZ; need transmission.
- Thread starter Dru27
- Start date
Big Tom
Active member
- 212
- 114
- 43
- Location
- Millington md
What trans do you need ,have a good used out of a m35a2
Big Tom
Big Tom
Big Tom
Active member
- 212
- 114
- 43
- Location
- Millington md
I am in Maryland can ship it to you if you want or call Boyce Equipment in Utah has them ready to ship a little closer than me
Big Tom
Big Tom
- 669
- 150
- 43
- Location
- International Falls, MN
Also Jacks Government Surplus in Tucson will have plenty of transmissions.
Katahdin
Active member
- 1,303
- 24
- 38
- Location
- Scarborough, ME
Is this you per chance? The pictures were taken near Glenwood Springs around March 21.
LiveFreeOrDieTryn2B
Member
- 779
- 20
- 18
- Location
- Springfield AR
If you are needing any advice on the phone if you are swapping it out yourself.PM me Ill be glad to help.
Katahdin
Active member
- 1,303
- 24
- 38
- Location
- Scarborough, ME
The sighting was posted on the M35A2 Group Facebook page, there's a guy there willing to ship you a transmission for as low as $350 plus shipping. No local help as of yet tho.
https://www.facebook.com/groups/52368678497/
Jericho
Well-known member
- 1,180
- 69
- 48
- Location
- Landaff NH
If it’s servicable 350$ is dirt cheap !!! It’s not a bad job. Just heavy. I did one in a M109a3 in a Wally World parking lot in NJ Two four by fours across the tops of the doors with windows rolled down and a chain fall. Get a good quality chain fall avoid Harbrum frieight Took me a week end by my self. Drain your fluids. Strip the floor panels and away you go I changed the clutch ect while I was in there. Manager was very helpful , NJ state police were less than nice , constantly reminded that I wasn’t allowed to do that in a parking lot. Constantly asked about fluid loss. Manager stepped up and reminded police it was private property. Wally land , drove away as trooper came to visit in afternoon of second day as he was telling me he had called for tow truck. Luckily I had a spare and had a friend drive it down to me Take your time. Do itcright. Good luck !
I will keep this in mind, thank you Katahdin. If i cant get it going i wll be looking for advice or just swap out the trans. I did get new synchros for 2-3 and 4-5. I replaced everything, i thought correctly but now it has a horrible grinding noise and 2 wont stay in gear. i have not moved the truck more than a couple of feet as i was testing it. I think i got the one bushing turned around but i didnt see how it would fit under the gear for second. I am looking at the diagrams that i could find and from those it looks like it may be backwards. if anyone has better pics of the break down of it and or the reassembly of it, it would be greatly appreciated. I am only taking out the main gear shaft and doing the work that way with out taking the trans down. If i have to take it out i will but i am trying to avoid it unless i need a new one. Just thought you all would like the update!
I forgot to ask where would the transmission be coming from?
LiveFreeOrDieTryn2B
Member
- 779
- 20
- 18
- Location
- Springfield AR
Im sorry Inforgot you didnt remove counter shaft. Id check shift forks and syncros.
Last edited:
Katahdin
Active member
- 1,303
- 24
- 38
- Location
- Scarborough, ME
The guy with the $350 transmission has parts sources in Florida and Mississippi, I know he ships through Fastenal, which you do have one of those in Flagstaff. I'll PM you his contact info.
- 6,984
- 2,520
- 113
- Location
- Montevideo/Uruguay
2nd gear spins directly on the shaft. Maybe you are referring to the 5th gear sleeve? The collar of that sleeve/bushing goes towards the back of transmission. (Some older diagrams had it wrong.)
Last edited:
That is the way that i have it in. I get clatter now, i start with the clutch in and then release it enough to see all the gears spin then push it back in and it starts to clatter really bad. it seems to lighten up a bit as a play with the gears. I also now have a seized top plate i have to go unfreeze. The top plate is also making a clicking noise. any thoughts on that?
Also i am on the back end of throwing an event where i am just breaking even and am running out of money and dont have enough to purchase and ship new parts as well as have enough for fuel to get home. I have not been working for a month except on this event. just to give a little back story as to where i am at and what is going on with me. I am just looking for advice on what is going on, i am starting to hit the end of my mechanical knowledge though.
Thanks for all of your help and advice.
Also i am on the back end of throwing an event where i am just breaking even and am running out of money and dont have enough to purchase and ship new parts as well as have enough for fuel to get home. I have not been working for a month except on this event. just to give a little back story as to where i am at and what is going on with me. I am just looking for advice on what is going on, i am starting to hit the end of my mechanical knowledge though.
Thanks for all of your help and advice.
Big Tom
Active member
- 212
- 114
- 43
- Location
- Millington md
Do you have the top cover off when working the clutch? If so be shure gears are in the right positions if not they will grind you should install cover before trying.
Big Tom
Big Tom
- 2,096
- 646
- 113
- Location
- Orlando, FL
At this point I would see if I could get someone to tow or trailer me home before I run out of money. The alternative is park it some place until you can get enough money and parts together to go get it.