- 7,744
- 154
- 63
- Location
- Columbus Georgia
Started on Swiss's CUCV - he can tell you what his plans are - but the build has started.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Project time once again Swiss's CUCV
- Thread starter zout
- Start date
- 7,744
- 154
- 63
- Location
- Columbus Georgia
As usual - a couple more
papabear
GA Mafia Imperial 1SG
- 13,520
- 2,469
- 113
- Location
- Columbus, Georgia
Whooo Hoooo!!! Is this gonna be the pink one you mentioned yesterday?
- 7,744
- 154
- 63
- Location
- Columbus Georgia
TiggerGF handcuff pink - yes
- 7,744
- 154
- 63
- Location
- Columbus Georgia
It runs perfectly fine on the liquid mixture I have - a few know personally what that is - it makes it shy of explosion and gets anything moving 
Besides posting in your new thread about down time - here is what I do in my down time instead of screwing around on here making Mods and Admin fustrated.
Besides posting in your new thread about down time - here is what I do in my down time instead of screwing around on here making Mods and Admin fustrated.
- 2,733
- 863
- 113
- Location
- Oakwood, Ga
Now wait a minute, how did you get the following done since PB left yesterday afternoon? I think you have a workcrew hidden in the back forest behind the pine tree?
1.) Interior Out
2.) Top Off
3.) Rear lights out
4.) Rear end sanded
5.) Take Pictures
6.) Drink Bud and leave on side rail
7.) Reply to PB posts on preamble
8.) Make phone calls to me and 73
9.) Start new post on CUCV
And you said you were going to clean the garage between projects???
Hummmmm something funny going on here. I am calling the drone back in for survalliance.
1.) Interior Out
2.) Top Off
3.) Rear lights out
4.) Rear end sanded
5.) Take Pictures
6.) Drink Bud and leave on side rail
7.) Reply to PB posts on preamble
8.) Make phone calls to me and 73
9.) Start new post on CUCV
And you said you were going to clean the garage between projects???
Hummmmm something funny going on here. I am calling the drone back in for survalliance.
Last edited:
- 2,733
- 863
- 113
- Location
- Oakwood, Ga
WTG I did some early recon on the fuel problem. The throttle shaft is dry going into IP. No other leaks around return hose etc. Taking off the IP top requires removing choke assembly etc so I did not dig any deeper yet. The evil Dr. Zout was yelling to get the CUCV to his laboratory, so I will attack fuel issues once I get the beast back.
- 34,012
- 1,810
- 113
- Location
- GA Mountains
Hmm, guess that's one way to fend of Ron!
- 7,744
- 154
- 63
- Location
- Columbus Georgia
Actually today was kick off time after getting out of the Dr's office. Around the windows really needed sanded by hand as the paint was sooooooooo thick it would just chip off - so when I re-coat it will have its surface to stick to where it belongs. Will get that bumper off the front with the grille and most likely sandblast them both as an assembly - they get painted the same color - but ain't tellin ya what color that is.
That is epoxy 2k primer sealer to seal up everything underneath that looks really great for a subsurface - it has great adhesion as well - the 2k will give it a nice coat to lay this color on - ain't tellin what color that is either.
This 2k will get block sanded with 400 when its all done before paint - I just wanted to start getting stuff I opened up sealed off.
That is epoxy 2k primer sealer to seal up everything underneath that looks really great for a subsurface - it has great adhesion as well - the 2k will give it a nice coat to lay this color on - ain't tellin what color that is either.
This 2k will get block sanded with 400 when its all done before paint - I just wanted to start getting stuff I opened up sealed off.
- 4,811
- 746
- 113
- Location
- Liberty Hill, SC
Sweet. Looking good there DR. Z
- 7,744
- 154
- 63
- Location
- Columbus Georgia
At least next time when Swiss tries to kill Ron in the woods and has to haul his carcass out - he can be hauled out in style 
papabear
GA Mafia Imperial 1SG
- 13,520
- 2,469
- 113
- Location
- Columbus, Georgia
Ummm... I heard Ron say he would rather die in the woods than ride in a CUCV...At least next time when Swiss tries to kill Ron in the woods and has to haul his carcass out - he can be hauled out in style
- 2,733
- 863
- 113
- Location
- Oakwood, Ga
The funny thing is that I told Ron I was going to get the CUCV to haul him out of the woods and you know what his response was?At least next time when Swiss tries to kill Ron in the woods and has to haul his carcass out - he can be hauled out in style
"No thanks I will drive the 4 wheeler out" Looking back on broken pelvis and ribs and all I think he really does not like the CUCV's
So Ron did the self Rescue!!!
- 2,733
- 863
- 113
- Location
- Oakwood, Ga
Zout WOWWWWWWWWWWWWWWWWWWWWWW. I still can not believe the headway in a few hours, I will be reviewing survalliance tape when I get back in town to see who is all working on this with you
Most Awesome.
Most Awesome.
- 2,733
- 863
- 113
- Location
- Oakwood, Ga
Hey did PB back into my passenger fender with the wc-22, I don't remember that passenger fender dent???
papabear
GA Mafia Imperial 1SG
- 13,520
- 2,469
- 113
- Location
- Columbus, Georgia
No Sir... I did not back the WC into your fender.
Zout had a basketball on the hood of your truck and BabyBear was trying to "rock" the truck to make the ball fall off!!
I'm glad zout hasn't posted a pic of the other side before he gets it repaired....
Attachments
- 7,744
- 154
- 63
- Location
- Columbus Georgia
You mean this pic of his drivers side NOW !!
- 34,012
- 1,810
- 113
- Location
- GA Mountains
Good grief Dave, what's the holdup? It's been 2 days, why in the heck is this project not done? Warp drive out of service?