amgeneral72
Active member
- 487
- 124
- 43
- Location
- HOLLY SPRINGS GA
Just had some of these sitting around, and I was bored.
If anything it looks cool.
If anything it looks cool.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Reconfigured CUCV front end with Infa-Red light
- Thread starter amgeneral72
- Start date
- 4,292
- 1,779
- 113
- Location
- Edmond, Oklahoma
Good idea
Havent seen that before.
i personally would have left slave port where it was and put light underneath.
Any pics of the install?
Looks like passanger BO light was painted over
Havent seen that before.
i personally would have left slave port where it was and put light underneath.
Any pics of the install?
Looks like passanger BO light was painted over
- 34,012
- 1,810
- 113
- Location
- GA Mountains
That would be great of one had NODs. LOL. I like it.
- 5,580
- 349
- 83
- Location
- DESOTO, KANSAS
Pretty sure he is running one of the newer LED BO lights and just looks painted over. Btw where did you wire the IR to?
Last edited:
tonkasal
New member
- 23
- 0
- 0
- Location
- Atlanta / GA
- 5,580
- 349
- 83
- Location
- DESOTO, KANSAS
Duh, I am pretty sure the "passengers side" should have been the big clue! It was my former Army training kicking in, BO drive light = BO Light , BO marker= BO guide, light or cat's eye.
Anyways did you end up putting an LED BO drive light on it, I got some for my MV's at GA last fall as they were going for what I thought was a cheap price.
Anyways did you end up putting an LED BO drive light on it, I got some for my MV's at GA last fall as they were going for what I thought was a cheap price.
cpf240
Active member
- 1,479
- 5
- 38
- Location
- Free in Northern Idaho
Really guys? I think he is talking about the big IR light where the relocated NATO jump start plug used to be...
amgeneral72
Active member
- 487
- 124
- 43
- Location
- HOLLY SPRINGS GA
At first I mocked it up with the light on the bottom, but after moving some stuff around I liked this look better. The slave port was easy I just turned it over and re bolted it in place. I did have to make a small bracket to secure the bottom to the rad support, but that only took a few minutes. And I didn't take any pics.
Oh and that is just the masking tape still on the BO light.
amgeneral72
Active member
- 487
- 124
- 43
- Location
- HOLLY SPRINGS GA
Did you take a look at those LED BO headlights that we all bought? They won't work on the older stuff. The pattern is different for the screw holes. They will work on the newer 9 series 5 tons. Well one worked on mine. They will also work on a bicycle with a 9 volt battery.
Last edited:
- 4,236
- 3,322
- 113
- Location
- Near Austin, Texas
Being me, I had to know what it would have looked like without moving the slave port from the normal position, so a couple of minutes in Paint, and...
I think amg72 got it right the way he did it, looks much more balanced, and aesthetically pleasing. Down low would still work, but looks kinda weird. Just my
Cheers
I think amg72 got it right the way he did it, looks much more balanced, and aesthetically pleasing. Down low would still work, but looks kinda weird. Just my
Cheers
- 4,292
- 1,779
- 113
- Location
- Edmond, Oklahoma
Yes
I was talking about the BO light on the bumper.
I do like the idea a lot
Just stands out more with the slave port moved.
Agree that it would look weird with the light below slave port
If I had NVGs, that mod would be a must do!
I was talking about the BO light on the bumper.
I do like the idea a lot
Just stands out more with the slave port moved.
Agree that it would look weird with the light below slave port
If I had NVGs, that mod would be a must do!
amgeneral72
Active member
- 487
- 124
- 43
- Location
- HOLLY SPRINGS GA
I haven't wired it to a switch yet. I figured I would wire it into a factory CUCV service / drive light switch since they have two power positions and a off position. Up for high & down for low. Will probably mount the switch with a label in the blank plate to the right of the steering wheel.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 758
- 113
- Location
- Cincy Ohio
I come with a good idear every once in a while!
- 2,011
- 73
- 48
- Location
- Orlando, FL
I like it! I think the slave port looks good where it is. The IR light is level with the headlight blackout. 
bikeman
Well-known member
- 2,894
- 502
- 113
- Location
- Ft. Bragg, NC
I think it looks great!
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Agreed! I need two for a good excuse to get the NVGs.
- 4,292
- 1,779
- 113
- Location
- Edmond, Oklahoma
The more I look at it, the more I like it.
Two would be be too much
The one is just right and looks factory.
Nice and balanced where it is
I've changed my mind
I like it a lot
Now.......lets see....$10k for a set of ANVIS 9's or another 5 ton or two CUCV's ????
Two would be be too much
The one is just right and looks factory.
Nice and balanced where it is
I've changed my mind
I like it a lot
Now.......lets see....$10k for a set of ANVIS 9's or another 5 ton or two CUCV's ????
gottaluvit
Well-known member
- 1,786
- 29
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
I was thinking one for each powered MV I have. I think a generation back NVGs only cost about $4k.
infidel got me
Well-known member
- 1,679
- 32
- 48
- Location
- Newberry, Florida
Looks good to me, nice looking truck by the way!