- 454
- 70
- 28
- Location
- cincinnati/OH
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Saturday Dec 30 HASPIN day-trip in Laurel, IN
- Thread starter Shrapnel
- Start date
Wire Fox
Well-known member
- 1,252
- 161
- 63
- Location
- Indianapolis, Indiana
I think he's hoping the hard top being latched in will put in some extra resistance and reduce the flex. I wonder how this will end for the hard top...
Sent from my SM-G530T using Tapatalk
- 454
- 70
- 28
- Location
- cincinnati/OH
That truck sure does flex hard. That's why I have been hesitant about removing sway bar links on the land rover untill I extend my brake lines. Shrapnel has an awesome rig
Sent from my SM-G935T using Tapatalk
I think my rusted out rocker panels combined with no hardtop allowed the body to flex too much. The fender cutting may have also contributed. Just not as much structural integrity as it had from the factory.
I’m planning to eventually weld in rectangular tube for rock guards which should also help. Then, long term goal, a roll cage.
Until then, I’ll try to go easy on my rig!
I’m planning to eventually weld in rectangular tube for rock guards which should also help. Then, long term goal, a roll cage.
Until then, I’ll try to go easy on my rig!
- 454
- 70
- 28
- Location
- cincinnati/OH
Ill believe that when I see it...
Wire Fox
Well-known member
- 1,252
- 161
- 63
- Location
- Indianapolis, Indiana
So my rig is still down. I got everything back together, got fuel back through the IP again, but can't get any fuel through the injection lines. Getting pretty clueless at this point.
Sent from my SM-G530T using Tapatalk
Sent from my SM-G530T using Tapatalk
- 2,664
- 2,209
- 113
- Location
- Sunman Indiana
Don’t know anything about what your working on, but did you try cracking the lines at the injectors instead of the pump end, to bleed the air out?
Wire Fox
Well-known member
- 1,252
- 161
- 63
- Location
- Indianapolis, Indiana
Yeah, I'm working at the injector end of the lines, because the IP side is impossible to access with the intake manifold in place. Working on a 6.5L HMMWV.
Sent from my SM-G530T using Tapatalk
Dang, it's cold outside and getting colder! Hope you all are still good to go. I''m planning to get down there around 10am Saturday morning. I'll be leaving my house around 8am with 1 or 2 guys riding with me.
Looks like it will be around 0 degrees F that morning. Run plenty of antigel in your fuel!
Looks like it will be around 0 degrees F that morning. Run plenty of antigel in your fuel!
- 224
- 97
- 28
- Location
- Rushville, IN
I still plan on coming down. I sure hope my heater is good!
- 454
- 70
- 28
- Location
- cincinnati/OH
I plan to be there early sat morning you guys want to meet at our campsite from last time?
Sent from my SM-G935T using Tapatalk
Sent from my SM-G935T using Tapatalk
- 1,079
- 57
- 48
- Location
- New Palestine Indiana
I still plan on meeting you about 09:15.
- 224
- 97
- 28
- Location
- Rushville, IN
Sounds good DJones. Dress warm!
I don't know if I remember how to get to the campsite. If DJones does, I am ok with that.
I don't know if I remember how to get to the campsite. If DJones does, I am ok with that.
- 454
- 70
- 28
- Location
- cincinnati/OH
I'll meet at the office at 10 so we all can find each other easy
Sent from my SM-G935T using Tapatalk
Sent from my SM-G935T using Tapatalk
- 224
- 97
- 28
- Location
- Rushville, IN
Are you going to have a fire going at the campsite? I can bring some wood if you need some. I have lots of it.
- 454
- 70
- 28
- Location
- cincinnati/OH
I sure Can! I will get there early and start the fire. I will use what I find in terms of wood but I sure would welcome some more
Sent from my SM-G935T using Tapatalk
- 224
- 97
- 28
- Location
- Rushville, IN
Ok, I will bring some.
- 454
- 70
- 28
- Location
- cincinnati/OH
Dave is meeting me early on Saturday and anyone around Cincinnati is more than welcome to roll out with us. I have a couple more seats.
