• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Special delivery

8

87cr250r

Well-known member
1,267
1,988
113
Location
Rodeo, Ca
If you want it to last in this application, SKF is the most reliable option. If you want better pricing check Bearing Engineering. The SKF 6305-2RS bearing is $35.

The long life bearings will be lubricated with polyurea grease.
 
Last edited:
jcollings

jcollings

Well-known member
Steel Soldiers Supporter
560
391
63
Location
Jupiter/FL
The original bearing that I had on the failed unit was the same number, although it was old style clay based Grease, which separates and is no good, this new style bearing they changed which is a much better Grease as you're aware of I'm sure.

I paid $16.43. $35.31 shipped to my door, so I guess that's good.

Sent from my SM-G975U using Tapatalk
 
jcollings

jcollings

Well-known member
Steel Soldiers Supporter
560
391
63
Location
Jupiter/FL
It's in there, but it looks like rain so I'm packing it in,
for all the torqing and wiring and hook up and blah blah blah that's for later time.
Just love putting those nuts on underneath those mounts,
whose fingers fit in there that's a bunch of c***haha


Sent from my SM-G975U using Tapatalk
 
Guyfang

Guyfang

Moderator
Staff member
Moderator
16,795
24,155
113
Location
Burgkunstadt, Germany
Look at picture #2 in post #30. Turn the zip ties, so the "zip tie clamp" is against the side of the gen set. Keeps the wires away from the side of the set. You will probably never run the set long enough to have a problem with wire chafing, but this is something we always did, and it helps keep chafing a non problem. In the control panel, especially on the bottom left side, this is a problem. By the diode board.
 
Mullaney

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,724
19,777
113
Location
Charlotte NC
Guyfang said:
Look at picture #2 in post #30. Turn the zip ties, so the "zip tie clamp" is against the side of the gen set. Keeps the wires away from the side of the set. You will probably never run the set long enough to have a problem with wire chafing, but this is something we always did, and it helps keep chafing a non problem. In the control panel, especially on the bottom left side, this is a problem. By the diode board.
Click to expand...
.
Wow. That's the voice of experience. Especially since everything on a generator is fighting vibration. The "zip side" easily gives you an extra eighth of in inch of "rub resistance" safety margin.

Thanks for sharing that @Guyfang
 
F

Farmitall

Well-known member
Steel Soldiers Supporter
544
276
63
Location
Eubank, KY
Guyfang said:
Look at picture #2 in post #30. Turn the zip ties, so the "zip tie clamp" is against the side of the gen set. Keeps the wires away from the side of the set. You will probably never run the set long enough to have a problem with wire chafing, but this is something we always did, and it helps keep chafing a non problem. In the control panel, especially on the bottom left side, this is a problem. By the diode board.
Click to expand...
Good idea on the zip ties, I do that same thing and you can also use a couple of small sections of split loom on the harness.
 
You must log in or register to reply here.
110,926members
165,351threads
2,326,672posts
1,636online users
Top