Stop water on the floor 2 man set up

[hummer4x4guy]

Guys I just got in the following AMG parts today to work on solving the issue of rain water from flooding the front of the truck. Part #'s are 5938744A for the aluminum bracket piece and 5939988 for the "seal-cargo Flr/back pan.
My plans are to prime and paint it and attach directly to the bulkhead. If you have the front tie downs installed this can slip under those and the bulkhead will still bolt in. If this setup keeps water out enough without rivits or bolts I'll just run it like that. To each their own if this is a problem for your truck and rain.

 

[olewhiskey]

Neat !

 

[GMVguy]

Guys I just got in the following AMG parts today to work on solving the issue of rain water from flooding the front of the truck. Part #'s are 5938744A for the aluminum bracket piece and 5939988 for the "seal-cargo Flr/back pan.
My plans are to prime and paint it and attach directly to the bulkhead. If you have the front tie downs installed this can slip under those and the bulkhead will still bolt in. If this setup keeps water out enough without rivits or bolts I'll just run it like that. To each their own if this is a problem for your truck and rain. View attachment 556705

Cool! Will these parts work for the 4-man bulkhead setup as well?

 

[hummer4x4guy]

I assume they would mlacek.

 

[hummer4x4guy]

Mlacek, on 2nd look you would need two brackets and two seals or neoprene seal of some type on the bottom. The seal that is designed for it doesn't stick on its essentially a round rope kinda seal. I'll post some photos later when I get home to show the underside.

 

[hummer4x4guy]

Here is a photo of the underside of the bracket and the seal that is designed to work with it. If ya need two side by side it would make sense to cut the brackets in the middle on both ends that would touch to remove the small section which doesn't have the grove to accept the seal to sit under it

 

[GMVguy]

View attachment 557311
Here is a photo of the underside of the bracket and the seal that is designed to work with it. If ya need two side by side it would make sense to cut the brackets in the middle on both ends that would touch to remove the small section which doesn't have the grove to accept the seal to sit under it

Excellent - thanks!

 

[hummer4x4guy]

You're welcome.

 

[trooper632]

Where did you order the part from

 

[hummer4x4guy]

Www.bluehummer.com or www.hummerpartsguy.com.
I ordered from bluehummer

 

[73m819]

Just drill some holes to let the water out.

 

[hummer4x4guy]

Doing it this way: A. keeps from adding holes to a nice body B. is an easy project to do to keep the water out, not just let it in then out.

 

[Pablo66]

I'm doing something similar for my 4 man. I'll post some pics when I get out to my shop.

 

[ClarkeF]

I have a similar piece that goes all the way across the bed. It was designed for a civilian 4DHT truck

 

[GMVguy]

I have a similar piece that goes all the way across the bed. It was designed for a civilian 4DHT truck

Got a part number?

 

[dpsmith]

Those bulkheads were added to keep cargo from shifting into the front. They will help keep some water out but not all of it .

 

[hummer4x4guy]

Hense the reason for adding the secondary item with the floor seal.

 

[whistlepig]

Curtain to floor sealing

Looking for ideas to keep the draft out on my 2 man soft top rear curtain. I can't be the only one that ever tried to address the situation. Besides going with an artic top kit or an application of duct tape how do you military guys or anybody for that matter ,seal up the draft?

 

[hummer4x4guy]

Do you have the bulkhead divider installed?

 

[whistlepig]

yeah,I've got a bulkhead in place .The cold air seams to make its way around and under the curtain.