• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

towing/pulling in reverse

tsmall07

tsmall07

New member
542
4
0
Location
Springfield, VA
Re: RE: towing/pulling in reverse

CCATLETT1984 said:
reverse in the transmissions of most trucks (someone confirm this) are straight cut, so you have stronger gears but loud at speed.
Click to expand...
^^Truth^^.
You usually wouldn't have as much reduction in R as you would in 1st though. Less reduction = less torque.
 
bottleworks

bottleworks

New member
920
2
0
Location
Central NC
Re: RE: Re: RE: Re: RE: towing/pulling in reverse

CCATLETT1984 said:
i would say with an auto trans, you'd be likely to burn up the clutches.
Click to expand...
When in reverse, line pressure is increased to prevent this. Line pressure is also boosted when you put the trans in Low/1.
 
Big Mike's Motor Pool

Big Mike's Motor Pool

Member
Supporting Vendor
574
-21
18
Location
Browns Mills NJ 08015 (next to Fort Dix)
i have pulled alot of people out of the mud when we are four wheeling. i find it to be easier on the truck if you use reverse low range. pulling on somthing lower than you exerts downward pressure. this plus the weight of the engine over the single front wheels makes it way easier to use your trucks weight and power to its fullest potential
 
rizzo

rizzo

Active member
2,841
8
38
Location
Port Huron, MI
I always thought that because of the reverse idle the gear ratio was just a tad lower in reverse than first. Is this true?????
 
M

Maroman

New member
18
0
1
Location
Forth Worth, Texas
+1 on not pulling out a vehicle with a M900 series in low transfer reverse. I was on ATD once in 29 palms. I was looking forward to marrying up with my wrecker there and having some fun. Some bonehead had tried to pull a 5 ton out of some sand in low reverse. He split the t-case in half. I was not happy. I spent the next week installing a rebuilt unit. My M936 was never the same. It is even plastered on the dash NOT to do it. To make it worse he was not even a wrecker driver. Obviously whoever issued him a trip ticket does not know how possesive we can be about our "issued" wreckers!
 
Recovry4x4

Recovry4x4

LLM/Member 785
Super Moderator
Steel Soldiers Supporter
34,012
1,808
113
Location
GA Mountains
The Allison reverse is like 11 to 1 (from a previous post). Combine that and low range and something is going to give.
 
rizzo

rizzo

Active member
2,841
8
38
Location
Port Huron, MI
Recovry4x4 said:
The Allison reverse is like 11 to 1 (from a previous post). Combine that and low range and something is going to give.
Click to expand...
[thumbzup]

know anything about the reverse idler lowering the reverse gear ratio?
 
spicergear

spicergear

New member
2,307
26
0
Location
Millerstown, PA
I also feel that because of the load on the nose; engine, pulled line, etc... that you have far greater traction on the singles (similiar to what mudlord said) than pulling from the rear. In certain applications the rear, because of all the tires, doesn't have the contact pressure on the tires and will easily just spin. Plus that doesn't help load the nose at all. I've spun the truck around and pulled logs out in reverse that would just make the truck spin pulling forward.
 
gringeltaube

gringeltaube

Staff Member
Super Moderator
Moderator
Steel Soldiers Supporter
6,983
2,517
113
Location
Montevideo/Uruguay
sailor2000 said:
What is the gear ratio in 1st gear and what is it in reverse in the M35 series?
Click to expand...
Spicer 3052 (5th direct): 1st = 7.55, R = 7.36
Spicer 3053A (5th o.d.): 1st = 5.01, R = 4.90

G.
 
You must log in or register to reply here.
110,655members
165,167threads
2,324,057posts
1,573online users
Top