Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
I was trying to keep my cables to the right and to the bottom.BC the diagram really helped THANKS.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
VIC-1 Install
- Thread starter Varyag
- Start date
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
I just got my RT524,R442 and my Vic1 Intercom installed.All them channels and not one person to listen to.If you decide to do this it was not cheap,it surprised me around $1,400.
Attachments
Last edited:
- 4,301
- 3,130
- 113
- Location
- Fort Worth, Texas
Looks really good there BB. I too hope to rig up something of the sort for CB radio and such. Nice airsoft guns too.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Hmm, you've got your R-442a/VRC hooked upto a MX-6707/As-1729 setup? Does it receive OK?
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
Its the MX-6707 antennas,dont know if it all works right yet.The antenna clicks when I change some of the stations on the RT-524.And when I hold the mic or the radio on the headset the fan on the RT524 really gets fast.Still trying to figure this whole thing out.I found out one of my new MX-6707 antennas does'nt click when I change channels,so I use it for the R442 radio.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
OK, I haven't seen the MX-6707 hooked up to an R-442a/VRC just yet. I'm use to seeing the AB-15 w/MS-116a, MS117a, and the MS118a used.
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
I guess I need to check on this,it uses the same coax cable as the rt524 CG-1773.
Armada
New member
- 3,046
- 4
- 0
- Location
- Buick City, MI
Sounds like it's working properly. The 'clicking' from the antenna is the auto adjustment of the frequency range.
The 'gets really fast' sound when you hold the mic, is the cooling fan in the back of the radio. They make alot of heat when transmitting. You can see the intake for it on the back side, make sure it doesn't get blocked off.
You used to be able to get TV stations on the rt524, but I don't think so anymore since they've gone digital.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Oh forgot to mention, your setup looks outstanding!
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
I looked on army radio and it listed the the MX-6707 and the AS-1729 antennas for the R-442.I just wonder which frequency to set the antenna for the R-442,or do you.
Army Radio Sales Co.
Last edited:
Varyag
Member
- 927
- 2
- 16
- Location
- Garfield, Washington
Welp, got tired of pinching my hand every time I wanted to turn it on and off so me and my Dad decided to rewire the whole mess.
Only this time I had access to a pile of brackets, a mx7777/grc and some much better soddering ability from my paps. I think the new setup is a heck of a lot better. I placed the 1780 behind the shifter on a new bracket I made and re-wired all the power through a new fuse block and the 7777. I'll post pics tomorrow. It was dark when I finally got everything pieced back together.
Only this time I had access to a pile of brackets, a mx7777/grc and some much better soddering ability from my paps. I think the new setup is a heck of a lot better. I placed the 1780 behind the shifter on a new bracket I made and re-wired all the power through a new fuse block and the 7777. I'll post pics tomorrow. It was dark when I finally got everything pieced back together.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Ahh, going to leave us hanging Matt? I was going to put my AM-1780 in the same place as you but I acquired an M66 reinforcement plate for the '68. Hmm not sure where I'm going to put it now. May need to fabricate a bracket to have it sit just above the bench seat back.
Varyag
Member
- 927
- 2
- 16
- Location
- Garfield, Washington
Sorry man, my internet took a crap last night. I am putting it behind the shifter
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
I got my radio cover today from Fair radio,it fits rather nice over my RT-524 and R-442 under the passenger seat.This cover is very well made and the price was very resonable at $33.00 shipped.It adjusts to differant lengths,I think 26" to 37" with snaps.
Attachments
Varyag
Member
- 927
- 2
- 16
- Location
- Garfield, Washington
Finally
Here are some pics of the install. It really just worked out nice.
Here are some pics of the install. It really just worked out nice.
Attachments
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
Looks great nice job.I was thinking of doing mine like that,but wanted mine a little closer to me to turn the knobs.But yours is out of the way for a middle passenger.
Varyag
Member
- 927
- 2
- 16
- Location
- Garfield, Washington
That is the biggest issue, my wife rides center and my kid on the side in a car seat. It couldn't block her feet. I actually had her sit in it before i bolted everything down just to make sure she had plenty of room.
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Great spot Matt. Install looks real clean and it looks like it belongs there! Great job man
Armada
New member
- 3,046
- 4
- 0
- Location
- Buick City, MI
Nice, well thought out install I like it!
Billy Bobbed
Active member
- 1,346
- 13
- 38
- Location
- Terre Haute,Indiana
Varyag if you want your CX-13089 cable to go to the back of the cab instead of towards the front,take the four screws out of the 2 connectors on the side of the MX-7777/A and you can turn them towards the front,back or down if they get in the way.I have mine towards the back.And my switch is still to the front.
Attachments
Last edited: