- 323
- 69
- 28
- Location
- New River, AZ
Good on ya, mate!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
- 323
- 69
- 28
- Location
- New River, AZ
The word on the side says everything. UN, like Undisciplined, Uncoordinated, Uncaring, Unethical, Unorganized, Uncontrolled, Uncouth, Untrained, etc.... I think you get my point.
- 323
- 69
- 28
- Location
- New River, AZ
Loved the videos, thanks for sharing. You part of Down Under sure looks different (& better) that where I lived (Woomera).
What's that thing bolted to your dash that your GPS is sitting on? Almost looks like the upper portion of a dual rifle mount.
- 1,010
- 4
- 38
- Location
- Annapolis MD
Got some 20gauge steel and made 2 new ceiling panels for the shop van. Installed in a HD parking lot(long story)
Attachments
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
How did you build the radius into those sheets (they look great); you got some kind of roller jig or something?
pitpawten
Active member
- 259
- 199
- 43
- Location
- Centreville, Maryland
This whole project is looking great man...how did you do the bends in these panels they look pretty smooth
- 1,010
- 4
- 38
- Location
- Annapolis MD
Measured twice then carefully bent the steel around a 4inch section of pvc pipe .
Big Dumb Truck
Member
- 152
- 0
- 16
- Location
- Birdsboro Pa.
I just finished up my brake light project. it turned out better than I thought it would. I rewired the lights and added some new ones. I started this project because I had a short in the wiring that I couldn't find. I'll be doing the front lights soon.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
- 327
- 51
- 28
- Location
- Bakersfield, CA
Those look awesome and factory quality! Nice work!
I just finished up my brake light project. it turned out better than I thought it would. I rewired the lights and added some new ones. I started this project because I had a short in the wiring that I couldn't find. I'll be doing the front lights soon.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Big Dumb Truck
Member
- 152
- 0
- 16
- Location
- Birdsboro Pa.
I'm going to put a Gadsden plate on the passenger side.
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Sent from my SAMSUNG-SGH-I337 using Tapatalk
chwhite0783
Member
- 55
- 0
- 6
- Location
- toms river/nj
installed my Jatonka spin on oil filter kit. easy to install. touched up the rattle can paint job a little bit. next to do is check the brakes and adjust and front axle boots
- 4,299
- 3,132
- 113
- Location
- Fort Worth, Texas
Jeepsinker and Nofearnohope were giving me a hand today getting some 109s back on their feet. First one is alive and well. More to come.. also the perk of working with a wrecker (shade!)
Attachments
Aussie Bloke
Well-known member
- 725
- 373
- 63
- Location
- Lost, out bush in OZ
G'day everyone,...
Correct!
That's exactly what it is, the double rifle retainer/rack.
Give that man a cigar!
Aussie.
Correct!
That's exactly what it is, the double rifle retainer/rack.
Give that man a cigar!
Aussie.
speedfellon
Member
- 34
- 0
- 8
- Location
- grass valley ca
Replaced missing rear axle bolt and installed AVM hubs on front axle. went on a 150 mile trip on new hubs. nice to have no axles spinning and easier steering.
dmetalmiki
Well-known member
- 5,523
- 2,028
- 113
- Location
- London England
I was properly miffed when trying to park up my (recently) re acquired deuce. Bangs and judders despite shifting vehicle position forward and backwards to "relieve" the pressure of "wind up". No use!. Today I decided to fit a set of freewheeling hubs. Problem eliminated, But will drive normally with the hubs locked as the (old version) deuce is a permanent 6x6 version. We never had this problem with the Kraz Zill or Ural.
My friends deuce bust the sprags with this problem and is now rear wheel drive only now.
Can a member "in the know" shoot us a fix, For the banging, and the fix for the broken sprags.
My friends deuce bust the sprags with this problem and is now rear wheel drive only now.
Can a member "in the know" shoot us a fix, For the banging, and the fix for the broken sprags.
Attachments
- 6,556
- 13,941
- 113
- Location
- Hawthorne, NV.
Ordered seals and dust boots for PTO and seals for Garwood winch.
- 6,070
- 4,440
- 113
Not my deuce, but I'm in the process of flipping hubs, mounting mrap rims and 395's, and changing out different fluids...
scboolitcaster
Member
- 277
- 4
- 18
- Location
- Belton, SC
I'm guessing it's not supposed to look like that...
Water? Or just old.
- 6,070
- 4,440
- 113
It looks like muddy water ecause it contains a large amount of muddy water.... so did the primary fuel filter....
Tomorrow will get me a look into the rear diffs and the transmission and hopefully a good look at the wheel bearings.
It's the wheel bearings I worry about. At least the diffs had some oil along with the water.
More pics to follow...