- 18,551
- 5,928
- 113
Bummer.
Contrary to popular belief, that is NOT a "new and improved" aerodynamic design. It may even increase your drag by a factor of 0.00000001 or so.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your 5 ton this week?
- Thread starter dezert ratt
- Start date
Contrary to popular belief, that is NOT a "new and improved" aerodynamic design. It may even increase your drag by a factor of 0.00000001 or so.
bchauvette
New member
- 810
- 12
- 0
- Location
- Easley SC USA, 29640
You know that was the first thing that came to mind when I heard the crunch. Then I uttered some words that is going to impede my progress to heaven.
- 3,871
- 497
- 83
- Location
- Gray Court SC
It can be fixed don't sweat it.
It's only metal as my buddy was not hurt all is good.
It's only metal as my buddy was not hurt all is good.
Another Ahab
Well-known member
- 18,007
- 4,582
- 113
- Location
- Alexandria, VA
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Hey mdemars03, glad the code violation worked out for you. Hope I don't ever have to deal with that issue. Also congratulations on the new truck. I love my M923
mdemars03
Member
- 254
- 0
- 16
- Location
- El Paso, Texas
Thanks!! Felt good to get that call from code enforcement.That's terrific!
Cheers to you, Brother.
mdemars03
Member
- 254
- 0
- 16
- Location
- El Paso, Texas
Thanks!! I hope nobody has to go through that. I know it will happen to someone, but you can always hope. And I love the 923.Hey mdemars03, glad the code violation worked out for you. Hope I don't ever have to deal with that issue. Also congratulations on the new truck. I love my M923
Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
Opening day! 2 each! I forgot to take a pic with them hanging from the spare tire hoist. Pulled out a fellow hunter who had slid his truck into a wet rut with the 923
Last edited:
Another Ahab
Well-known member
- 18,007
- 4,582
- 113
- Location
- Alexandria, VA
Still a little early isn't it?
Did you take them with a bow? Shotgun? Or is it already rifle season in NC?
Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
Yep, Rifle season opened today! Bow and black powder have been in for a month for one and 2 weeks for the other. I broke in a new stand too. I worked hard on it during the off season and finally got it up 3 weeks ago. The 923 helped!
I shot both of mine within 3 min of each other in the same area. My father in law did the same thing less than 10 min later at the other end of the field.
- 2,811
- 41
- 38
- Location
- Mt. Eden, KY
Nice talley, 4 plump does. Now the real works starts but it will be worth it. Pass the mashed potatoes please.......
Headed into the woods tomorrow w/ a muzzle loader. Rifle season opens 11/14/15 .
JC
Last edited:
Another Ahab
Well-known member
- 18,007
- 4,582
- 113
- Location
- Alexandria, VA
That's something, you all start early.
I remember losing all my carpenters in November when I was a construction project manager working jobs here in D.C.:
- Maryland rifle season was always around the middle of November.
- And then the Virginia carpenters would disappear about a week or two later.
You were expected just to "know" that; used to drive me bananas!
- 1,200
- 457
- 83
- Location
- Spartanburg,SC
Busy day for me today. Coffey1 helped me rebuild the fuel selector valve, change both fuel filters, install an engine block heater and coolant bypass filter on the 932A2 today. We also unspooled the winch and verified it worked. Since it had never been used, we found out that the hydraulic lines were crisscrossed. I'm ready for the Rally.
- 1,450
- 121
- 63
- Location
- Gray, GA
When i bought my truck the singles had already been installed but the thimbles had been reused. I had bought the proper lug nuts a while ago and finally got around to putting them on. After a quick trip down a bumpy dirt road they were re-torqued, painted and marked.
- 959
- 38
- 28
- Location
- Loxahatchee, Florida
Worked on my spare M35A2 engine assembly today removing the bumper. Used my 3/4" drive breaker bar with a 3" extension on those 12" long bolts !
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Hey Ford Mechanic, nice opening day. Hope I have some luck on Monday, opening day of archery season here
Love the idea of using the spare tire crane to clean and butcher the deer.
Love the idea of using the spare tire crane to clean and butcher the deer.
Broke out my M923a2 to run into downtown SLC to my work so I could pickup a shipment that I had delivered to my work address and then drove up to Fort Douglas (UofU campus) to catch the UMVC swap meet before returning to work and then finally home. Got a bunch of thumbs up from the people arriving to the stadium for all the tailgating activities for tonight's game ASU vs UofU
therooster2001
Active member
- 824
- 44
- 28
- Location
- Colorado
Took off my painted tan mudflats, and swapped with original black ones. I love my tan color, but everything is painted (not the cab inside). For some reason it really bugged me that those and the engine shields were tan. I need to paint the engine shield metal tan and I'll feel better.
Ford Mechanic
Active member
- 1,805
- 7
- 38
- Location
- Edenton, NC
Works great, this was the first time my father in law had seen it done that way. His back had been giving him problems and want looking forward to cleaning them on the ground. Pic from last yearHey Ford Mechanic, nice opening day. Hope I have some luck on Monday, opening day of archery season here
Ddmk18
Member
- 272
- 2
- 18
- Location
- James Creek PA
Got around to installing my electric control valves for the hydraulics that way I have my winch control, dump bed, knuckle crane (needs installed) and an auxiliary line. I wanted to run everything off the trucks PTO. I have two more custom switches coming
