- 18,541
- 5,852
- 113
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your 5 ton this week?
- Thread starter dezert ratt
- Start date
wadefreedomvehicles
Member
- 354
- 5
- 18
- Location
- Orem, Utah
I didn't take any pictures....
Im so bad at the whole picture thing.
Im so bad at the whole picture thing.
gottaluvit
Well-known member
- 1,786
- 28
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Sprayed saltwater all up under it! That is the bad part. Good part is it ran like a champ on a 250 mile round trip pulling an M1082 trailer loaded on the return with 3700 lbs and snow covered roads. Had to lock in the front differential coming up from the valley close to my house on an unpaved road. It had a couple inches of snow and a 100' drop off with no guard rail. Thought it best to not wait til it was too late to lock it in.
Spyderman
Active member
- 393
- 37
- 28
- Location
- Alexandria KY
Took the truck out in the snow. Love the icicles.
Sent from my webslinger!
- 1,178
- 390
- 83
- Location
- Guymon, OK
Got tired of changing heater blower motors, this is the 4th ruined motor between 2 trucks. Used a mrap vent fan, will do a write up when I get to building the 2nd motor. 2nd photo is a comparison between old and new motor sizes
How to do this is written up here http://www.steelsoldiers.com/showth...or-Mod-with-MRAP-blower&p=1963919#post1963919
How to do this is written up here http://www.steelsoldiers.com/showth...or-Mod-with-MRAP-blower&p=1963919#post1963919
Last edited:
Another Ahab
Well-known member
- 18,003
- 4,565
- 113
- Location
- Alexandria, VA
big block 88
Member
- 862
- 17
- 18
- Location
- Topeka/Kansas
Plugged the block heater back in for the nasty cold coming again. I see there is coolant leaking from somewhere by the oil cooler. I see a small pool of coolant on the ground under the truck also in the same area.
Anyone have any idea what it might be? Its too **** cold to go try and hunt down the leak.
Anyone have any idea what it might be? Its too **** cold to go try and hunt down the leak.
- 3,222
- 392
- 83
- Location
- Tonopah, AZ
I would check your hose clamps.
big block 88
Member
- 862
- 17
- 18
- Location
- Topeka/Kansas
Hose clamp is what im hoping for. All i felt like doing in the cold was grabbing it and checking the hose for tightness. It "seemed" tight. Supposed to warm up in the next week i should be able to get out and check it out.
Its been exposed to - temps several times this year im hoping the oil cooler didnt crack or somthing a long those lines.
Its been exposed to - temps several times this year im hoping the oil cooler didnt crack or somthing a long those lines.
big block 88
Member
- 862
- 17
- 18
- Location
- Topeka/Kansas
If i can ever move all my **** deuce parts i will get the barn cleaned up again and start piling parts for the 5 tons. Issue this year was we got our 925 running and a friends 923 running so the few parts i had have been exhausted.
- 1,450
- 120
- 63
- Location
- Gray, GA
I'd appreciate a write-up. My surplus guy has one that I planned on picking up for the same purpose. The data plate showed it pulls 28A though. If it creates much better heat and volume I'll give it a shot.
therooster2001
Active member
- 824
- 44
- 28
- Location
- Colorado
Might also be the petcock down there.
- 1,178
- 390
- 83
- Location
- Guymon, OK
you are correct on 28 amps, the heater CB is 30 amps, so just squeaked under. I only run mine on low, high speed sounds like its going to eat through the fire wall, but this is also the first run, so there will be upgrades.
FullSpecial
Active member
- 247
- 108
- 43
- Location
- Denton TX
Replaced one of these;
Funny how one little part can shut down the whole operation......
Funny how one little part can shut down the whole operation......
- 1,653
- 1,669
- 113
- Location
- Nova Laboratories, WA
Given the temps, did you check for dihydrogen monoxide in the lines?
- 805
- 71
- 28
- Location
- Kennewick, WA
Sent from my TRS-80 using Tapatalk
- 1,178
- 390
- 83
- Location
- Guymon, OK
Swamp Donkey here is the write up on the build http://www.steelsoldiers.com/showth...or-Mod-with-MRAP-blower&p=1963919#post1963919
Another Ahab
Well-known member
- 18,003
- 4,565
- 113
- Location
- Alexandria, VA
FullSpecial
Active member
- 247
- 108
- 43
- Location
- Denton TX
Ha, good one! It was oily though, inside and out. Undetermined if 90w or motor oil. Mind you I have seen nothing
at the air drains.