- 4,290
- 1,777
- 113
- Location
- Edmond, Oklahoma
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your CUCV today/lately - Part 2
- Thread starter Warthog
- Start date
NovacaineFix
Member
- 662
- 1
- 18
- Location
- San Diego, California
cucvrus
Well-known member
- 11,474
- 10,437
- 113
- Location
- Jonestown Pennsylvania
I replaced 2 sets of the worn out oil soaked rubber radiator support insulator pads. This may put me into CUCV Hot Rodding but lets go give it a whirl.
I used Prothane Motion Control. Sounds erotic. Radiator insulators Prothane Part # 7-712-BL they fit all GM big block radiator supports on 68-91 Chevy / GM cars and trucks. It was not broke and I fixed it. It was plum worn out and doing nothing. I will be doing this to Terminus M1009 also. I hate to disturb that fine gem. But sometimes you just gotta do what you gotta do. Looks like a great day today. I have lots of work and some fun working on Easter find M1008. I will post my results later. Have a great day and make the best of it.
I used Prothane Motion Control. Sounds erotic. Radiator insulators Prothane Part # 7-712-BL they fit all GM big block radiator supports on 68-91 Chevy / GM cars and trucks. It was not broke and I fixed it. It was plum worn out and doing nothing. I will be doing this to Terminus M1009 also. I hate to disturb that fine gem. But sometimes you just gotta do what you gotta do. Looks like a great day today. I have lots of work and some fun working on Easter find M1008. I will post my results later. Have a great day and make the best of it.
rustystud
Well-known member
- 9,284
- 2,994
- 113
- Location
- Woodinville, Washington
I went to the "Prothane" radiator mounts years ago and they work great !
ridenby
Member
- 144
- 18
- 18
- Location
- Frankfort,Ky
Used Rosscommon method to convert to 12volt system. Installed LMC headlight relay wiring. Forgot how much fun changing starter on 4x4 chevy can be. Power bled front brakes,rear bleeders are being ----.
ralbelt
Active member
- 1,056
- 9
- 38
- Location
- West Warwick, R.I.
Rebuilt the front calipers, replaced brake hoses and bleeders. Replaced rear brake cylinders, retension springs,made up new metal lines and replaced rear hose, also small line from proportioning valve to rear hose connection. I had trouble forming the short bends at the valve so for now I bypassed it.
Last edited:
Chevybrit
New member
- 177
- 2
- 0
- Location
- Northern Pasquotank NC
Fixed short under dash to solve indicator and stop light issue, pulled dash appart and got volt meter, oil pressure and dash lights working!
CUCVLOVER
Active member
- 2,352
- 9
- 38
- Location
- west Tennessee, just outside Milan
Today I replaced the king pin bushings and springs in the front axle. The truck had grown a case of death wobble and the new springs and bushings has basically solved it. Still a slight shake here and there but there's probably my tires. I'm happy for now.
gottaluvit
Well-known member
- 1,786
- 28
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Used mine for campaigning from Saturday through Tuesday, but since nothing political is allowed on this site, no pictures can be uploaded. Had a lot of horns blasting and waving and hootin' 'n hollerin', and a few photo taking times! Used a couple tanks of fuel, all at an average of 25-30 mph. Hit every town in my vacinity. This site may ban politics but as long as our country allows it, I proudly participate.
Chevybrit
New member
- 177
- 2
- 0
- Location
- Northern Pasquotank NC
Stripped out the rear brakes and rebuilt cleaning and painting a few parts!
Last edited:
Another Ahab
Well-known member
- 18,003
- 4,565
- 113
- Location
- Alexandria, VA
It looks like new U-bolts on your leaf springs, too. Did you replace those recently?
Chevybrit
New member
- 177
- 2
- 0
- Location
- Northern Pasquotank NC
No previous owner did the lift ... also pinched the brake line on the drivers side rear.. What do you think ..did the brake even work??
Last edited:
Another Ahab
Well-known member
- 18,003
- 4,565
- 113
- Location
- Alexandria, VA
PJL
Member
- 140
- 6
- 18
- Location
- Way south of Seattle, WA
That pinched line probably helped keep the brake shoes from wearing out.
rustystud
Well-known member
- 9,284
- 2,994
- 113
- Location
- Woodinville, Washington
OK, that was funny !
rustystud
Well-known member
- 9,284
- 2,994
- 113
- Location
- Woodinville, Washington
Time to get some "stainless steel" brake lines !
- 653
- 533
- 93
- Location
- Reydon, OK
Stainless steel won't work any better UNDER the u bolt!!
- 888
- 1,321
- 93
- Location
- Rhein-Main Area, Germany
lol.....lol.....
rustystud
Well-known member
- 9,284
- 2,994
- 113
- Location
- Woodinville, Washington
Really ? That's what you took from my comment ? Well then let me explain in simple terms. First take the 'U' bolt off, then remove the old brake line. Then replace the 'U' bolt (making sure to torque it to the proper specs) and then install a new stainless steel brake line. Bleed the brakes. Better ?
- 653
- 533
- 93
- Location
- Reydon, OK
Sorry Rusty if I offended you in any way. I just couldn't resist my one liner. I meant it to be funny like the above post #4693 that the pinched line helped keep the brake shoes from wearing out. I knew fully what you meant and just expected everyone to know it was all in fun.