Jonas
New member
- 53
- 0
- 0
- Location
- Stockholm/Sweden
A big contact hanging by the restistor pack... i think it has to do with the glowsystem? Il get a picture tomorrow but if anyone knows what I mean please post 
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Whats this contact for? m1009
- Thread starter Jonas
- Start date
niferous
Member
- 715
- 6
- 18
- Location
- Houston, TX
That's a little vague. A picture would help for sure.
blitzengine
New member
- 87
- 7
- 0
- Location
- Valdosta,GA
Jonas
New member
- 53
- 0
- 0
- Location
- Stockholm/Sweden
OL AG '89
Member
- 743
- 9
- 18
- Location
- Kingwood, Texas
Um maybe for fuel filter connections, still really vague.... check the TM
looks like it has 8 wires.... can you get the wire colors.... with that and the TM, wiring diagram you can figure anything out...
where does it come from?
looks like it has 8 wires.... can you get the wire colors.... with that and the TM, wiring diagram you can figure anything out...
where does it come from?
niferous
Member
- 715
- 6
- 18
- Location
- Houston, TX
I'm thinking fuel filer. Does your truck still have the factory rectangular fuel filter?
Jonas
New member
- 53
- 0
- 0
- Location
- Stockholm/Sweden
Okay, might be it, il get the wirecolors tomorrow.
I dont think the rectangular fuelfilter is being used.
i got a electrical pump mounted below the battery trays so i guess it has been taken away.
Okay guys, don't out guess the CUCV Guru.......LOL
It is the connector for the ICE/STE diagnostic system. On a stock system the wiring harness goes thru the firewall and mounts to the bottom of the dash. The harness has the round Cannon plug, Tach Buffer module and the Resistor Board. Figure 56 of the TM 9-2320-289-20P
Unless you need the diagnostic system you can leave it as is.
If you look closely you will see the 4th pin connector is missing.
Wire colors for the 8 pin connector are :
Red
black w/white stripe
brown
empty
pink
tan
gray
black
Right click on the thumbnail and choose "Open Link in New Window"
It is the connector for the ICE/STE diagnostic system. On a stock system the wiring harness goes thru the firewall and mounts to the bottom of the dash. The harness has the round Cannon plug, Tach Buffer module and the Resistor Board. Figure 56 of the TM 9-2320-289-20P
Unless you need the diagnostic system you can leave it as is.
If you look closely you will see the 4th pin connector is missing.
Wire colors for the 8 pin connector are :
Red
black w/white stripe
brown
empty
pink
tan
gray
black
Right click on the thumbnail and choose "Open Link in New Window"
Attachments
Last edited:
Jonas
New member
- 53
- 0
- 0
- Location
- Stockholm/Sweden
haha indeed you are the guru. )) my diagnostic system is taken away, so i think its this too
)) my diagnostic system is taken away, so i think its this too
OL AG '89
Member
- 743
- 9
- 18
- Location
- Kingwood, Texas
Joe YOU THE MAN....
Was going to be my next suggestion.... No guessing here....
Unfortunately didn't have the TM stick handy.... couldnt perform complete search....
after doing so, I concur with Warthog......
ps. the figure 56 is acting strange, when I try to right click to print it wants to print the entire thread.....
Was going to be my next suggestion.... No guessing here....
Unfortunately didn't have the TM stick handy.... couldnt perform complete search....
after doing so, I concur with Warthog......
ps. the figure 56 is acting strange, when I try to right click to print it wants to print the entire thread.....
