Who has a receiver on their 5t?

[skav]

I'd like to pull a trailer with a 2-5/15 ball and curious if and how anybody has installed a receiver on a 5t. I would like a 2-1/2" shank and 20,000lb capacity.

If you have a receiver, please post pictures.

 

[quickfarms]

I used a curt 15605 if my memory is correct.

 

[74M35A2]

Did you search the existing threads? There are plenty of leads already.

Do you want to retain a pintle hitch? Also depends on your 5t, some are different in the rear. Some people have done beautiful work to make their own, some here sell kits, and the best fit store bought one I have seen (IMO) is in the "What have you done to your 5T?" thread.

 

[skav]

I'll search a bit more. I would like to retain the pintle.

 

[swbradley1]

TM America (on here) has an unusual way of doing a hitch but I don't have any pics and I don't know if he sold any of them. I saw one on an 813 though.

He cut a plate and put holes in it. You removed the pintle and use longer bolts and it fits under the pintle. He was going to sell all the pieces and you welded it yourself.

Super simple and I saw the truck pulling a trailer with another vehicle on it so it was strong although I had asked him for a mod if I bought one.

 

[Warthog]

What type of truck? The M809 and the M939 series will be different. Also double check your specs in the first post. I have never seen w 2-5/15 ball or a 2-1/2" shank.

 

[Warthog]

TM America (on here) has an unusual way of doing a hitch but I don't have any pics and I don't know if he sold any of them. I saw one on an 813 though.

He cut a plate and put holes in it. You removed the pintle and use longer bolts and it fits under the pintle. He was going to sell all the pieces and you welded it yourself.

Super simple and I saw the truck pulling a trailer with another vehicle on it so it was strong although I had asked him for a mod if I bought one.

Here is TM America's version



Post #27
http://www.steelsoldiers.com/showthread.php?45005-Curt-receiver-hitch-for-the-Deuce-18-000lb-1-800lb

 

[M35A2-AZ]

I used a Curt 15530 it has a 16k load and a 2' receiver, the curt 15605 is a 18k and has 2.5" receiver. When the receiver is in it the pintle is turned a little, but with it removed the pintle works fine.

It cost around $175

http://www.steelsoldiers.com/showthread.php?101670-M931-32-2-inch-receiver-hitch&highlight=receiver

 

[swbradley1]

Here is TM America's version

View attachment 595859

Post #27
http://www.steelsoldiers.com/showthread.php?45005-Curt-receiver-hitch-for-the-Deuce-18-000lb-1-800lb

That must have been his first one, the one he had at Haspin was about the area of 1.5 shoe boxes under the pintle.

 

[Warthog]

Is this the one?



http://www.steelsoldiers.com/showthread.php?101670-M931-32-2-inch-receiver-hitch
Post #35

 

[swbradley1]

That must be it. I do remember the small plate on the front under the pintle and the other plate being behind the pintle but I think his final design both plates were about the same size. The stars for chains were in the small plate down on the lower corners.

 

[armytruck63]

I like the hitch M35A2-AZ used. I think I would figure out a way to mount the glad-hand supports differently so that I could move the hitch towards the rear of the truck a few inches.

 

[droprat]

My son and I modified and built this bumper pull hitch that someone had scrapped. We also modified and installed this RV 5th wheel hitch.]

 

[DJones]

I used a curt hitch also that is rated at 15,000#.

 

[74M35A2]

I like the hitch M35A2-AZ used. I think I would figure out a way to mount the glad-hand supports differently so that I could move the hitch towards the rear of the truck a few inches.

I thought the same also at first, but if you look at his second picture, it looks almost up tight against the rear of the pintle hitch mounting castle nut.

I also used a Curt u-weld kit. It has side plates, not a bottom mount. It can shift fore and aft with enough load on it, which is something I didn't consider well when I purchased it. Now I need to add stabilization that way. I do like that I can have it fully rearward on the truck frame though. If you get a hitch that bolts to the bottom of the frame rails rather than the side, you won't have this problem. I hope somebody can learn from my mistake and not duplicate it.

 

[dmetalmiki]

I have this on the M54A2 camper as the hitch can be exchanged for a civilian dual 50mm ball hitch and adjustable pin pin hitch.
http://www.steelsoldiers.com/album.php?albumid=878&attachmentid=382057

 

[shadowdd]

Here red is the hitch that we made. Use it all the time and yes, we can still use the pintle hitch.

Bryan

 

[skav]

Here red is the hitch that we made. Use it all the time and yes, we can still use the pintle hitch.

Bryan

View attachment 597137View attachment 597138View attachment 597139View attachment 597140View attachment 597141

That's basically what I'm looking for. How does it pull the trailer? I have a 34' toy hauler that weighs in around 15k.

 

[shadowdd]

That's basically what I'm looking for. How does it pull the trailer? I have a 34' toy hauler that weighs in around 15k.

It is very nice, you have to watch how tight you back in in places so you don't pinch the front of the RV with the bed of the truck but it pulls like there is nothing back there!

Bryan

 

[440Duster]

On my M925A2, I fabricated mine using 4 inch, 3/8's angle iron with added bracing on the backside. Full use of the pintle is retained and is mounted as high as allowed to maintain departure angle in the back. Has held up to some heavy pulling. As for wiring, I made a 2 foot adapter cable from a military trailer cable to a standard 7 pin connector and run LED trailer lights.