Barneyszoo
New member
- 529
- 12
- 0
- Location
- Riverside, CA>
Can someone tell me what this pulley/trolley setup is, what does it do and will it fit on an M35
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Wrecker Front Winch
- Thread starter Barneyszoo
- Start date
- 7,584
- 363
- 83
- Location
- Cheyenne, WY
5 Ton winches are ALOT bigger than deuce ones.
Barneyszoo
New member
- 529
- 12
- 0
- Location
- Riverside, CA>
Ok but what does that pulley thing do?
deuceman51
Member
- 885
- 10
- 18
- Location
- Scotland South Dakota
That is called a level winder and its purpose is to help try and wind the drum in a neat mannor and keep the wire rope from crossing over itself and getting into a tangled mess. Winch trucks without that often will only wind(when winching) on one side which is responsible for the top plates on the winches getting bent. It shouldn't fit on a deuce because the winches are different and I belive the spacing will be wrong, someone else might know for sure.
Barneyszoo
New member
- 529
- 12
- 0
- Location
- Riverside, CA>
Cool, thanks I thought it was maybe some way to run the cable over or under the truck to pull out the back.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
hate to steal your thread but is the level winder the same as a gipsy head?
jwaller
Active member
- 3,724
- 19
- 38
- Location
- Columbia, SC
nope. separate ends of the truck.
level winders ONLY came on 5T (and 10T and bigger rear drag line setups M911 and M123) trucks and only originally on the front of the 816 and other 5T wreckers.
they can be fitted to any 20k garwood 5T winch but are not the only part of the system required to make it work. You MUST also install a tensioner so that the cable doesnt jump off the pulley when you unload the winch line.
your winch drum brake must also be in proper order so that the drum doesn't unwind when the putting tension on the cable and then releasing.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
so whats a gipsy head?
Barneyszoo
New member
- 529
- 12
- 0
- Location
- Riverside, CA>
No prob, I'm just learning. I'd like to get a 5 ton someday.
jwaller
Active member
- 3,724
- 19
- 38
- Location
- Columbia, SC
it's the pogo stick, as called by some.
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Still don't know what a Gipsy head or pogo stick is?
- 1,425
- 37
- 48
- Location
- Winter Haven, florida
Maybe this will help, the cable goes under the front roller and up and over the sleeve and lays down on the back side of the drum.
Attachments
Csm Davis
Well-known member
- 4,166
- 393
- 83
- Location
- Hattiesburg, Mississippi
Yeah Steve that's a level winder and if you look back they said it is not a Gipsy head.
- 1,634
- 741
- 113
- Location
- Central NY
Only thing that I know of that is anything like a "pogo stick" - is often a term for the 'hosetenna' on a tractor....... and therefore nothing to do with a W/W truck!!!
Is a gipsy head anything to do with a capstan type winch??
- 1,634
- 741
- 113
- Location
- Central NY
There should be a way to do it, but you'll need a few pulley wheels, associated brackets, pig tails etc., to safely route the cable smoothly to a rear fairlead past all the undercarriage etc.
Current thread on Mack wreckers has the fairlead on the front bumper - winch is way at the back (well, it's not right behind the front bumper anyway). Also a Land Rover 101 FFW(w/w) has a midships winch that pays out either end.
- 26,246
- 1,179
- 113
- Location
- NY
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
Not a bolt-on, but it's been done and details are on this site somewhere. There are concerns about overloading the front axle, among other things.
I've been thinking about center-mounting winches on my deuce and our 5-tons and it doesn't seem like it would be too complicated. Run the cable to the rear and around a pulley, then back to the front. Front pull would be single-line and rear pull would be double-line. Concerned about drag and the difficulties paying out cable though. Might not be manageable.
Jeepsinker
Well-known member
- 5,399
- 456
- 83
- Location
- Dry Creek, Louisiana
Just try paying out cable off of a rear M936 winch without bird nesting it and you'll forget all about your midship winch idea.
jesusgatos
Active member
- 2,689
- 28
- 38
- Location
- on the road - in CA right now
Actually just bought an M936A2, but it's not running so haven't had a chance to mess with it yet. Figured that a level-wind / auto-tensioner setup would be an essential part of that plan, and would obviously result in that much more additional drag. Was looking at the HET's, how they have those smaller winches to pay-out the main winch line. That might be an option. At a certain point, probably more trouble than it's worth, but there are some upsides to a single center-mounted winch too.
Jeepsinker
Well-known member
- 5,399
- 456
- 83
- Location
- Dry Creek, Louisiana
Yea even with the level wind and everything I had quite a hard time both paying out and rolling up cable. My level wind doesn't seem to want to function either.