- 9,604
- 1,493
- 113
- Location
- mid- michigan
Michigan is by the pound generally $1.00 a pound anr no plea bargins to get reduced if you have prior over load tickets. They generally write them to the company instead of the driver.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
2012 F450 Hauling 32,000 lbs. (5 TON)GVWR=44,500
- Thread starter decodeme2
- Start date
therealsundance
Member
- 412
- 17
- 18
- Location
- Lutherville, MD
Md is by the pound, iirc. Looks overloaded to me, but I'll let the OP let us know.
It varies state to state, some by the lb some percentage. Connecticut is a percentage, New York by the lb. And all seam to have a bracket system in place.
IE 5-10% is one value 10-15% another per hundred lbs. New York adds a kicker for precentage over axle weight. So not only do you pay for the weight but then they compile the axle fine as a kicker.
Here DOT watches for that kinda hauling. Driver with a pusher axle down or a pick-up hauling that load are sure signs. Not only is there a good chance being over-loaded but in this case the driver is probably not licensed for the weight. Your typical endorsement is up to 26,000.
So the likely hood of a class A driver driving the pick-up is slim. Where as a Class 8 truck with a over sized trailer probably has a permit. Of course most get checked for permits cause it's a nice fine if they don't have one or used the wrong bridge.
- 14,255
- 1,730
- 113
- Location
- Dayton, OH
Boy, the OP is going to be surprised if and when he ever posts again.......
- 26,246
- 1,178
- 113
- Location
- NY
Boy, the OP is going to be surprised if and when he ever posts again.......
Better off suprised here, than at his first DOT station!
spicergear
New member
- 2,307
- 27
- 0
- Location
- Millerstown, PA
I think something only just touched on is that whatever the payload capacity is on the truck...that weight can be taken off the loaded gooseneck weight as it technically shares the load. If the payload capacity is 5,000lbs and and the trailer is 25,000lbs (for discussion) then you pull that 5k off the trailer. Trailer weight now is considered 20k. Still doesn't get you around the rating of the coupler though...
flighht2k5
Banned
- 322
- 5
- 0
You guys are so funny. You'll complain and gripe all day long about someone carrying heavy weight with a civilian tuck. Then turn around and brag that your 2.5 ton carrying 30000 pounds or 5 ton tucks carrying 50000 pounds or whatever it is. Then you all high five each other for a job well done.
- 26,246
- 1,178
- 113
- Location
- NY
Wouldn't the trailer (and it's frame) simply be limited by its total capacity rating? If the trailer was rated for 12 tons, thats it. No matter how it's loaded (other than less, if it's impropperly loaded)
spicergear
New member
- 2,307
- 27
- 0
- Location
- Millerstown, PA
You're crazy Nevadian! Nobody does that! 
spicergear
New member
- 2,307
- 27
- 0
- Location
- Millerstown, PA
DH, I know what you're saying but they allow that with goosenecks since if the hitch is correctly located, it's loads the rear axle of the truck safely. You'll never, ever see any load off measure on a bumper pull.
A company Fayette Trailer is maybe 20mi from the farm and I check in with them from time to time. They had a big goose with tandems and dual with a bent front frame on it. The guy was hauling wood and had like 35,000lbs on it. It was only 20,000lbs overloaded...
spicergear
New member
- 2,307
- 27
- 0
- Location
- Millerstown, PA
At some point I may try to round up a big gooseneck for the 931 so I know what you're saying.
- 26,246
- 1,178
- 113
- Location
- NY
So, it would be sensible to register your goose neck, for more than it's max capacity. Here in NY, we register a trailer, for it's maximum load capacity(gets pricey).
That's interesting and confusing, on the weight transfered to the truck.
That's interesting and confusing, on the weight transfered to the truck.
- 2,799
- 73
- 48
- Location
- Mesquite, NV
I'm not a towing expert, but as I read the OPs post he says that 30% of his load is on the trucks rear axle. He said he checks rack axle to make sure it isn't overloaded and if so moves the load. That would be the same as a semi adjusting the trailer bogies.
I think anyway. That's how I read it.
I think anyway. That's how I read it.
spicergear
New member
- 2,307
- 27
- 0
- Location
- Millerstown, PA
Percentages are one thing but actual scaled axle load is another.
The other thing that will nail you is the actual printed Gross Combined Weight Rating (GCWR) the manufacturer puts on the truck. You go over the GCWR and you're rolling the dice.
The other thing that will nail you is the actual printed Gross Combined Weight Rating (GCWR) the manufacturer puts on the truck. You go over the GCWR and you're rolling the dice.
- 7,584
- 363
- 83
- Location
- Cheyenne, WY
He's just boosting his post count!You're no posting expert either, DUG.
Double post!
