- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M925A2 Delco Style Alternator
- Thread starter tractors0130
- Start date
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
Worked a 16 hour day today with internet access for less than a total of 60 seconds, just got home. Responding to SS is not priority #1 while at my real job. Apology, but reality.
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
.
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
Received tracking number.
Looking forward to a good alternator.
Thanks again!!
Looking forward to a good alternator.
Thanks again!!
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
I went with the genuine Delco-Remy 100A brushless Alternator.
Also bought the correct factory Cummins Alternator bracket for a clean install.
Almost went with the 130A model he has but was overkill since I'm not running any accessories besides a Garmin Dash Recorder.
The original alternator fried my ABS module plus fuses.
Also a PCB. Maybe my brand new one also.
Expensive repair. Sure it could be worse
Wish I would have done this mod when I first read about it.
Lesson Learned.
Also bought the correct factory Cummins Alternator bracket for a clean install.
Almost went with the 130A model he has but was overkill since I'm not running any accessories besides a Garmin Dash Recorder.
The original alternator fried my ABS module plus fuses.
Also a PCB. Maybe my brand new one also.
Expensive repair. Sure it could be worse
Wish I would have done this mod when I first read about it.
Lesson Learned.
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
Looks great!I run the Delco 130A. They're regulated, so it doesn't hurt to have extra, at least in my eyes
View attachment 657169
On the cummins bracket.
The 130A one he offered for sale was a Mitsubishi brand.
Wanted to stay with all USA parts on truck (minus Garmin).
And didn't need all that power.
Great thing......I can add it later if I add extra lights, etc.
Anythings gotta be better than the original one.
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
Installed new alternator
Life is good
Life is good
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
The Delco may be made in Mexico, so at least you can claim North American. Mitsubishi has alternator manufacturing in the US, Japan, etc.... Most of the Cummins engine castings occur outside of the US, majority being India and Brazil, etc, but, the oarts are finished and engine assembled in the target market country where they are sold. Over 50% of Cummins product is sold outside of the US. They are truly a genuine global company. Japan quality is on the opposite end of the spectrum as Chinese.
The Delco's I have are on clearance and $100 less than the 130A unit until stock is gone. Only a few left. Yes, even the Chinese Delco clone is way better than the stock alternator. You can close the hood, remove the volt meter, and shut the truck down in any switch order with no over-volt. How it should have been from the beginning.
Don't forget what I am in need of for my boat !!!
I have a buyer that paid and I don't believe I have his ship-to address. Took on a load of orders all at once so did not check specifics. I need to get his sorted out, as it has been 2-3 weeks already now, and it may be my fault, so I feel bad about it. Have emailed and PM'd him. Will refund 10% for the delay, apology.
The Delco's I have are on clearance and $100 less than the 130A unit until stock is gone. Only a few left. Yes, even the Chinese Delco clone is way better than the stock alternator. You can close the hood, remove the volt meter, and shut the truck down in any switch order with no over-volt. How it should have been from the beginning.
Don't forget what I am in need of for my boat !!!
I have a buyer that paid and I don't believe I have his ship-to address. Took on a load of orders all at once so did not check specifics. I need to get his sorted out, as it has been 2-3 weeks already now, and it may be my fault, so I feel bad about it. Have emailed and PM'd him. Will refund 10% for the delay, apology.
Last edited:
- 4,290
- 1,776
- 113
- Location
- Edmond, Oklahoma
LOL, No I won't forget.
The Delco unit is awesome.
Alternator and new bracket were very well packaged.
Will have to paint new bracket later. Was too cold and I needed truck fixed asap.
M925A2 was hooked up to my M989A1 and parked in a very inconvenient spot when old alternator fried. Literally.
Didnt want to start truck without new alternator in place.
Wish I did this a long time ago.
The Delco unit is awesome.
Alternator and new bracket were very well packaged.
Will have to paint new bracket later. Was too cold and I needed truck fixed asap.
M925A2 was hooked up to my M989A1 and parked in a very inconvenient spot when old alternator fried. Literally.
Didnt want to start truck without new alternator in place.
Wish I did this a long time ago.
Ford Mechanic
Active member
- 1,805
- 6
- 38
- Location
- Edenton, NC
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
They will throw me off stage by the scruff of my neck and my belt loops if I post a price here. I will PM you the cost.
Hah, I bet you weren't wearing pants when you posted that!
infidel got me
Well-known member
- 1,679
- 32
- 48
- Location
- Newberry, Florida
Grendel--- you have scared me for life!
- 3,222
- 392
- 83
- Location
- Tonopah, AZ
Nice!!!!
Hey man, I am really not that scary... Discoball, pants-less would leave me scarred for life, however.
One ball, hanging low... old age ya'know.
infidel got me
Well-known member
- 1,679
- 32
- 48
- Location
- Newberry, Florida
74M said he is working on a new ball leveling system right now. I heard it involves a 10# weight, a 130 amp delco alternator and lots of ice.