- 4,288
- 1,773
- 113
- Location
- Edmond, Oklahoma
That does help.I used 4-ga cable and soldered on copper terminal ends, then applied heavy-duty heat shrink over exposed wiring.
HTH.
Thank you!
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
That does help.I used 4-ga cable and soldered on copper terminal ends, then applied heavy-duty heat shrink over exposed wiring.
HTH.
Worked a 16 hour day today with internet access for less than a total of 60 seconds, just got home. Responding to SS is not priority #1 while at my real job. Apology, but reality.Ok
Good advice
sent at you a couple of PMs and haven't heard back. FYI
Sounds fair.Worked a 16 hour day today with internet access for less than a total of 60 seconds, just got home. Responding to SS is not priority #1 while at my real job. Apology, but reality.
Received tracking number.
Looking forward to a good alternator.
Thanks again!!
Looks great!I run the Delco 130A. They're regulated, so it doesn't hurt to have extra, at least in my eyes
View attachment 657169
On the cummins bracket.
What's the going rate for your kit?The Delco may be made in Mexico, so at least you can claim North American. Mitsubishi has alternator manufacturing in the US, Japan, etc.... Most of the Cummins engine castings occur outside of the US, majority being India and Brazil, etc, but, the oarts are finished and engine assembled in the target market country where they are sold. Over 50% of Cummins product is sold outside of the US. They are truly a genuine global company. Japan quality is on the opposite end of the spectrum as Chinese.
The Delco's I have are on clearance and $100 less than the 130A unit until stock is gone. Only a few left. Yes, even the Chinese Delco clone is way better than the stock alternator. You can close the hood, remove the volt meter, and shut the truck down in any switch order with no over-volt. How it should have been from the beginning.
Don't forget what I am in need of for my boat !!!
I have a buyer that paid and I don't believe I have his ship-to address. Took on a load of orders all at once so did not check specifics. I need to get his sorted out, as it has been 2-3 weeks already now, and it may be my fault, so I feel bad about it. Have emailed and PM'd him. Will refund 10% for the delay, apology.
They will throw me off stage by the scruff of my neck and my belt loops if I post a price here. I will PM you the cost.What's the going rate for your kit?
Sent from my SM-G900V using Tapatalk
Hah, I bet you weren't wearing pants when you posted that!They will throw me off stage by the scruff of my neck and my belt loops if I post a price here. I will PM you the cost.
Nice!!!!LOL, No I won't forget.
The Delco unit is awesome.
Alternator and new bracket were very well packaged.
Will have to paint new bracket later. Was too cold and I needed truck fixed asap.
M925A2 was hooked up to my M989A1 and parked in a very inconvenient spot when old alternator fried. Literally.
Didnt want to start truck without new alternator in place.
View attachment 657826View attachment 657827
Wish I did this a long time ago.
Hey man, I am really not that scary... Discoball, pants-less would leave me scarred for life, however.Grendel--- you have scared me for life!
that better not be my 130 amp delco alternator!74m said he is working on a new ball leveling system right now. I heard it involves a 10# weight, a 130 amp delco alternator and lots of ice.
We get it, advertisements are annoying!
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!