shawnshumvee
Member
- 336
- 6
- 18
- Location
- Janesville WI
Got finished with my TM hard copies. looking threw TM's as a pdf files in a pain in the neck, literally.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your HMMWV today/lately
- Thread starter Warthog
- Start date
Victorkilo31
New member
- 82
- 0
- 0
- Location
- San Diego CA
I'm thinking about doing the same thing you did. Is it broken down by one tm per binder?
Bravojmc
New member
- 512
- 5
- 0
- Location
- Palisade, Colorado
what will you sell a set for!?
shawnshumvee
Member
- 336
- 6
- 18
- Location
- Janesville WI
yes. This is a set of 3. I got the Am general's also and a bunch more. i printed them of at staples for $200. Not bad for over 5000 pages. i mean i printed everything i needed, even for my GETT and my M101A3 trailer.
shawnshumvee
Member
- 336
- 6
- 18
- Location
- Janesville WI
I got a AM general TM for $20
Victorkilo31
New member
- 82
- 0
- 0
- Location
- San Diego CA
That's not bad considering the amount of printing needed. I need to find a good print shop up here and get that done
shawnshumvee
Member
- 336
- 6
- 18
- Location
- Janesville WI
Victorkilo31
New member
- 82
- 0
- 0
- Location
- San Diego CA
Yeah I'm gonna have to do that. Gonna get my truck here first lol
Bravojmc
New member
- 512
- 5
- 0
- Location
- Palisade, Colorado
Pulled the dash for paint....
Action
Well-known member
- 3,576
- 1,557
- 113
- Location
- East Tennessee
Good time to replace the defrost hoses if they are crusty.
This is a good shot of the slot that allows the steering column to move up and down...
Victorkilo31
New member
- 82
- 0
- 0
- Location
- San Diego CA
Brings a question to mind. Any one replace the thin defrost/heater hose with something sturdier?
ryanruck
Active member
- 427
- 46
- 28
- Location
- Cincinnati, OH
Yes, with this stuff when I upgraded to my MRAP heater and added rear heat.
I had some extra hose and decided to replace the defroster duct with it. Only problem is it is too big to use to upgrade the floor heater ducting which is, I believe, 1.5" hose. It was a pain to get it through some of the openings the original ducting is made for since it is such heavy rubber but, it will fit with some effort.
No need to ever worry about it rotting again.
Victorkilo31
New member
- 82
- 0
- 0
- Location
- San Diego CA
Thanks for the info. Something I'll keep in mind once I see what shape mines in
Bravojmc
New member
- 512
- 5
- 0
- Location
- Palisade, Colorado
The hoses in the picture are all new!
The hoses I replaced had like 10 separations/splits...
Last edited:
General Hood
Member
- 712
- 2
- 18
- Location
- Fort Towson, OK
So.......I purchased a replacement front tie rod assembly. One tie rod end popped loose with minimal effort, but the other tie rod stud spins with the nut. GRRR, any suggestions?
Changing my handle to Lucky
Changing my handle to Lucky
- 5,614
- 2,922
- 113
- Location
- Metairie/La (N'awlins)
AutoZone or oreilly in the loaner tools have a tie rod fork. That wedged tightly should tighten the ball socket enough to get the nut off or it will need to be cut off.
infidel got me
Well-known member
- 1,679
- 32
- 48
- Location
- Newberry, Florida
If it's on the spindle side -- put a floorjack under it( tie rod end) and put pressure on it. You should be able to zip it off with your air gun now. #2 cut the nut off with cutoff wheel/grinder.#3 flamewrench
I think the tie rod end bolts in from the top -- so the floorjack thing wont work. You could try a prybar on it/while appling air gun
I think the tie rod end bolts in from the top -- so the floorjack thing wont work. You could try a prybar on it/while appling air gun
Last edited:
General Hood
Member
- 712
- 2
- 18
- Location
- Fort Towson, OK
Tie rod assembly removed and replaced. I had a tie rod separator fork but no amount of pressure this old man could apply was adequate to keep the bolt from turning, so grinding wheel saved the day. On to the next task ( long list to go) Thank for the tips Gentlemen
orgnal
Member
- 285
- 4
- 18
- Location
- Denver, CO
General Hood
Member
- 712
- 2
- 18
- Location
- Fort Towson, OK
Upon inspection, the dust boot on one of the tie rods ends was partially missing, and there was "play" on that same tie rod end, so I replaced the entire assembly . The idler arm, pitman arm, and other steering components seem to be in good shape