Search results

The back of the stereo has a yellow 5v and a blue remote. Any suggestions on where/what cable I might wire those too? Can i wire the yellow 5v into the main power? Thanks!

Awesome thanks. The previous owner did this prior, so the wires have been run from the battery to the fuse box etc. There is just a bunch of wires and I wasn't sure If i needed a harness.

Hi Guys, Wondering if this is the wiring harness I need to buy to install my stereo. GM Receiver Wire Harness For select Buick, Cadillac, Chevrolet, GMC, Oldsmobile, and Pontiac models, 1985-up at Crutchfield.com Thank you.

Thank guys, I was thinking that was the answer but didn't want to go there yet. It was a new/rebuilt hydrobooster before I opened it... Then I bought the rebuild kit and replaced the seals and put it back on. But I guess it's time to punt for a new one... ****ty

I've flushed the power steering system and followed the prodcedure for bleeding pressure out of the hyrdrobooster. However, everytime the ignition is applied the pedal goes to floor and front brakes lock. When I turn off the ignition the brakes release and the m1009 will roll etc. Have...

Looks like I'll need one of these for the seal inside? 2771004X Hydro-Boost Repair Kit (Mostly Rubber) or http://www.restorationperformance.com/servlet/the-127003/2771004-Hydro-dsh-Boost-Repair-Kit/Detail ****, should have just rebuilt my old one. As i've forced myself to rebuild the new one.

Does anyone have a part number on the seal that goes inside of the hydrobooster? Also could someone perhaps clear up how only when I press the gas pedal the problem arises. Is it some how linked to the power steering pump? Sorry for being an automotive inept.

I tried to remove the rod spring and 8 armed cup without taking apartt the hydrobooster. I couldn't remove the 8 armed disk/cup it seemed, without getting to the back side of it. I looked at the tech manuals, and my stupid haynes manual and there isn't a mention of it, or perhaps I couldn't find...

Thanks. I took apart the old one removed the spring and rod, then took apart the new one and installed the spring in rod. I tightened all the bolts as tight as I could without a torque wrench. When the truck is off and I press the brake, the unit doesn't seem to leak. I can turn on the...

Please help me. My hydrobooster is making brake fluid foam come out the side of it when the gas is applied... please.

Nevermind figured it out. I have to swap it. If anyone else encounters the same question. The answer is here. hydraboost installation conversion In short yes. "The spring and rod are an important part in the system; the spring puts tension on the booster piston so it releases the pressure...

Old One http://www.steelsoldiers.com/members/apoc-bane-albums-hydrobooster-picture10819-imag0041.jpg I kinda assume it needs to be in the new one to apply some pressure back from the brake pedal. But the bolts on the old one are in there good, and I would think the cost of a new hydrobooster...

New one http://www.steelsoldiers.com/members/apoc-bane-albums-hydrobooster-picture10820-imag0042.jpg

I bought a replacement hydrobooster as mine was leaking. The new one doesn't have a part that the old one does. Do I need to some how remove the part from the old one and install it on the new one? If so it seems like a lot of work to take out the bolts to seperate the two parts of the hydro...

I think you should replace the starter then proceed. Starter Military Equipment CUCV 6.2 Diesel 24 Volt 28MT: eBay Motors (item 290366555566 end time Jul-31-10 21:48:39 PDT)

Thanks for the Advice guys. I went to take pictures of the connection on the starter and discovered my problem. The () shaped connector on the large screw was touching the ignition key connector also. When I applied power the starter was in a constant state of ignition, which caused the ZAP...

Hoping I didn't fry some more stuff by the zap caused when I connected the first battery.

Hi. Background prior to question. Had rear main seal, oil pan, and oil pump replaced at shop. m1009 ran well for 3 days. Stopped starting only a click sound, after hearing power relay kick over, then turning the key. Tested batteries - tested good. Ordered new starter, thinking why not...

Thank you very much.

Should I buy the unit that comes with the master cylinder? Or just the booster?