Search results

Ok, here are some pics of the install. Just need to connect the leads to the generator but I want to run it and test everything before hooking it to the house. Only real questions are the grounding wire connection. I purchased an 8' ground rod, tamped it in, and connected the generator trailer...

Ok I actually found and interlock kit that should work for my older panel. The electrician is coming in the morning to do the panel work. I also finished the single phase conversion as shown by sewerzuk (very much appreciate that sir!) today. I will double check my wiring and connections...

Mine was under the bottom board as well. I just moved the wires and cut the bar while it was attached. Had to lengthen the X8A16B from T8 to make it to T3 by a couple of inches.

Here are some pics of the evaporator fan/box mounted behind the dash. I will be running some flexible ducting to the 4 under dash vents that will be installed later. Switches mounted in the dash for easy access. Fans blow pretty strong so with the refridgerant it will be nice and cool. Gotta...

There are the 11.00x20 firestones somewhere areound 43"or so. I don't know who was to be avoided selling MV's here, somebody else may chime in on that one.

I'll prob start a new thread just for the A/C part of my build once I am done so everybody can see the whole install in one shot. I have the evap box temporarily connected to the buss to make sure it works, go to go. I am planning to remove the inside of the glove box leaving the door in...

Popped out the instrument cluster to repair the squeaking speedo and cleaned it up while I was there. Gotta love that flexible circuiton the back of the case.. High Tech stuff, lol. Anyhow greased the cable coming in and also wd40'd the speedo unit on the backof the dial real well. Reassembled...

OK guys sorry for the delay! I finally have my power cord 60'4/3 SOOW, I am using an outside box with cable connectors for a semi perm install. I'll run a solid copper wire from the gen ground to the inlet box that contiues to the panel setup. I am using SER 4 conductor wire from the inlet box...

Finished the bottom end stuff and it runs great. Primed it before I started it at the vacuum drive. No leaks and fresh oil and filter with a quart of the lucas oil conditioner. Changed all the belts, swapped in new goodyear radiator hoses. Flushed the radiator, new coolant. I have a...

Tim is definitely the guy to talk to out there. Very cool GL employee and very helpful. Really everone there is pretty good some just more so than others.[thumbzup]

Got everything but the pan back in, new rear main seal using the plastic guide... Tq'd the bolts to 40ftlbs- 110ft inner 100ft outer, 60ft on the oil pump bolt. Laid down the anaerobic sealer on the rear main cap, oiled up the bearings and offset the rear main seal as per TM. Tapped it in and...

So I am taking care of that leak at the front of the engine, def the front seal on the oiil pan, and I have come across some other issues. If I have the pan off to do new pan seals I figured I might as well swap out the oil pump for a new one and do the rear main seal while I am there. Took...

Cool! Look forward to it. Thanks.

Good stuff! Looks great. Can you post some pics of the small lift you put on your M1009 also unless you have a thread for that as well. I am looking to put 2" TC springs and blocks on mine for a small lift.

Super badazz!!!! I wish I could do this!

OK time to order some stuff.. Firguring the 70-75 amp cable like these towards the bottom http://www.stayonline.com/sto-600-volt-bulk-wire.aspx or http://www.wireandcabletogo.com/Portable-Cord/600V-SOOW-STO/SOOW/4-3-SOOW-Portable-Cord-600V-Non-UL.html Also still trying to track down the...

Thanks for posting that DTOM stencil from milspec. That one is cool but I am more interested in the original style. I think what you and others said about going to a shop is the best idea. I'll be looking into this so I will post back with results. Thanks!

Gadsden Flag stencils???? I have been trying to figure out what to paint on the truck doors for the duece and cucv for a while. I finally came to the conclusion that some rattle snake stencils and "DTOM" under it would be awesome just like on the gadsden flag. Does anyone have any info on any...

Here are some pics of the fuel filter that came on this truck. Some guys were asking for some close up pics.

Wow, thanks man. Maybe I'll just put the ham in the deuce and call it good. Thanks for the info!