Search results

Thanks guys i will do that.

Yep thats my deuce, i was asking $4000 for it. Oh, by the way where did I leave it ?

I am going to build a press of some sort tomorrow to mount my 12.5 20 xl/s. Can anyone tell me what they used or have a picture of a press. I spent a long time today with backhoe with no luck. I have i beam and may build it like a verticle log splitter on steroids. pleas help. Local tire...

Well, the milemarker winch on my dodge Ram is a 2 speed (civilian) 12,000 lb. And I have the milemarker from the hummer which has a much larger hyd. motor so it has to be even better. I Bolted it to the bumper today and before the picture police get me (Sorry my batteries died on the dig...

Thats what I thought untill I bobbed my deuce. I can not see a docter using a 3 doller pair of scissors charging $120,000 for a simple brain sergury either. I drove 1000 miles to get my tires and a spring kit. And put a couple hundred hours on my back drilling and welding in temps as...

Going to find one tomorrow. I will probably use a power steering pump from a big truck. And may add power steering at the same time. I have read that a hummer winch is very strong using the stock steering pump so a big unit should do. I also have a 24 volt electric hummer winch that is huge...

I searched and cannot find if anyone installed an hhmv milemarker hyd. winch on a deuce. I will be starting the install tomorrow so any tips would help.

There is a place in ohio called reindl spring service. 419-524-3413 not sure about arching but may be a help.

Pm me a phone number. I can deliver 1 to you

Lifted the bed with backhoe to check clearence of pintol. Used 3/8 8 grade bolts with special frame nuts for hangers. My dad and I build hoists for dumps. Have some hoists but not sure which style to use yet. The avitar is a 87 WE-4 i sold to pay for land and green toys. Only put it there...

Dump mechanism not yet installed. May use a hoist off of one of my M105 DT 's Drive shaft needed 6 inch length added. Rear spring shackle re-uses the front bottom frame rivet hole and I have pictured the location of the front shackle.

Finnished my bobbed project yesterday. I do have one issue to deal with yet. I moved the crossmember that holds the pintol hitch forward 10 inches so the tailgate can swing open 90 plus degrees. However I used the M105 DT (dump trailer) bed instead of the standard M105 bed. When i dump...

I priced axles at kublos in PA for a friend.... $800 for a srearing and a little less for a rear axle. Thats where buying that one for $1500 makes sense. Get your axles and have alot left for shebay.

m35a2 WO/W running condition unknown but appears unused except for on sundays buyer loads... bring floordry

Thanks for the info. I had never heard of collusion? I feel enlightened. So is it ok to do this after you already bought a lot?

If he wants a bobbed deuce for $5000 he is probably still looking.:roll:

Can anyone save me the time mounting the axle and spring shackles on my bobb project. I can probably figure it out but If I had a couple shots of shackle location and cab to axle measures. I am using m35 front springs and shackles and a m105 bed. I figure the center of wheelwell is 60...

is he saying he wants to spend $5000 with single axle conversion done? I saw one at kublos yesterday I think $13000 done. m35 bed cut down and 9.00 20 duels on singl rear axle. Looked sweet. one on shebay less than 6k right now but will bring more

Towbar on EBAY!! Item number: 330306674518 Is that the one for an m35 or is it a lightweight?

Ok, I did find out you are right. Even if the bar does not fail but is being used when an accident occurs, I can be held responsible. Mainly because the total weight might exceed 26,000 lbs (hope you have a CDL) Even if I sell it as a USED bar I am responsible and can be sued. So untill...