Search results

Probably an air leak somewhere in the fuel system. Cracked hose or fuel filter most likely. How long did you try cranking after it died? One of my trucks will do that every few months. 10 seconds of cranking, sit for 2 minutes, repeat. Normally fires back up again after the 5th or 6th attempt.

Correct. That is why I wrote “civilian/CUCV”.

Yes, just swapping the top covers will get you 24 volt military or 12 volt civilian/CUCV set up. All of the GEP engines I have seen have the protected 5 sided safety Torx screw on them. Be aware a special tool might be needed. Here is the best listing of the part numbers to tell you what you...

Glad you got it figured out. After I wrote the above I went out and looked under the hood of my m1009 to make sure I had the wire colors correct. Something about the back of the drivers side alternator didn’t look right so I touched the bolted on red wire. It moved. So did the stud in the...

I am not sure what you mean by wired plug and plug on alt. There is the plug plug on the side that has 2 wires. One is always battery voltage and one (brown stock, white with replacement plug) that is 0 key off and battery voltage key on. There is also battery voltage on the red wire that...

The 6BT is over 1200 pounds fully dressed out. A 6.5 is about half that. Have some mercy on your front axle and kingpins. $800 is a great price as mentioned in the post above. Buy it and flip it. Also know that the NV4500 had a specific bellhousing for Dodge and a specific bellhousing for...

Well, 5 of them are trailers. But, yeah. I still have all of them plus a few sports car type things. My wife says I am a sick, sick, sick man.

I have used Motive screw on adaptors for other vehicles and love their products. I have not used their adaptor for the Chevy. I have though used several different Snap-On adaptors which look exactly the same and they all leak. 2 chains just don't disperse the clamping enough. Read the...

The 6.5 is an indirect injection engine. Horsepower is not what IDI engines do. They run great, awesome low rpm non turbo reliant grunt, good mpg without turbo help and with a turbo have the ability to push a driver back in the seat with a gleeful yell. I’m not trying to make this about me...

6.5 turbo quick facts. 1994 GM side mount turbo with mechanical injection pump. 1995 - 1999 GM side mount turbo with several different turbo sizes and an electronic IP. 2000-2002/2003 GM 6.5 turbo in vans had a block made for a center mount turbo with oil supply and oil return casted into...

Growing puddle of some liquid under the right wing tip during the video.

I had the same issue that was fixed a few months ago. Just the new O-rings on the pump sure make it seem like it runs stronger. With the Viton rings so cheap and kits available from surplus stores and all over E-Bay. I now consider this a normal maintenance item for every 10 years or so of...

I did misunderstand. You just want to plug the sensor hole in the radiator? Just buy a 1985 K30 6.2 coolant level sensor and be done. They are cheap. If you want to have an engine oil temperature gauge. The best place to put the sensor is on the side of the block above the oil cooler ports...

I think I know what you are asking for. Post #260 in this thread is I think the answer: https://www.steelsoldiers.com/showthread.php?74514-M1007-CUCV-Suburban-Clone-Build-Thread/page7

I went and found my 11 year old thread about this too. https://www.steelsoldiers.com/showthread.php?17290-Gasser-Cab-Install&highlight=

I’m 100 miles or so from you with a few spare gauges as well. What is the gauge doing exactly? If the needle just stays over past F then that is normally a sender issue. You can reach in over the tank from the drivers rear wheel area. That is where the ground wire several people already...

With the cab doors and roof off. An engine hoist works very well at pulling the cab off and on.

Exactly. The 1-1/2"-2" length difference is probably the issue. Adjust or lengthen your linkage.

Yes. All the doors that move inside there have some kind of seal on them. New seals make it really nice.

Alpine, when you get to doing the under dash stuff. Take the entire evaporator housing apart and put new foam in. It really makes a difference. Sharecropper, glad you got her on the phone. She was super nice when I spoke with her as well a few years ago. The holes in the brackets are sized for...