Search results

The green is a bit lighter than I'd like, but all in all for a little rattle can and time, fantastic coverage. We'll see how it looks after clear coat.

Sanded some panels down, hitting the rust again and buffing the gouges tomorrow, then paint. Gotta love rain days

Found the transfer case and transmission under the dirt and grossness from who knows how long, more importantly got to be soldier B while the ol lady whooped my bee hind as soldier A. First of my many projects she's taken interest in. Couldn't do it without you guys, huge thank you.

Didn't someone have a restoration of an hst not long ago? Be cool to see something like that......just saying......or HEMTT... A10.... You know, normal backyard stuff 🤣

So far I've found this bar measures 14in centerline to centerline, supposed to be 14 3/4. Right around an inch and a half of pedal travel, pedal is set to maximum height through the floor. The orange line looks backwards to me according to the TM, maybe I just read it wrong. Onward we go.

I'm having the same problem, thought it was in the shifter shaft, took advice from @gringeltaube and drew the conclusion it wasn't. If nobody minds a little thread resurrection/hijacking I'm knee deep in going in through the top. So far aside from pedal play, measurements check out but I can't...

Return from center, I didn't know it was supposed to stay when tilted towards the passenger side. They (synchros) shouldn't be but who knows. Can't diagnose anything properly with the clutch dragging and out of adjustment though, and putting what's happening with what you explained equals the...

Dyslexia strikes again. Google says Eaton, TM says Spicer, data tag says 3053, I'm sure more corrections will be necessary. Firstly there's what seems to me to be too much slop in the shifter, and when shifting from 3 to 4, well simply put it doesn't want to. Grinds terribly, just feels like...

So what started as a wiring job ended as three jobs, which I'll be documenting as I go. This one is to fix a shifting issue which is still unknown between the shifter shaft, the 4-5 shift lever, and probably the clutch. Starting here I'm using TM 9-2520-246-34-1 as reference and hoping for the...

My lift pump hasn't worked since I got the truck, not sure why yet, but my guess is it's something to do with the keyed ignition wiring. My plan is to take wire 76 off of where it usually gets power and move it to my switch panel, giving me true control of the pump. If I find my pump is...

"Knowing" one cylinder had low compression, and two cylinders had bad rings, I'd say it's time for a compression test. If ever you're told one cylinder is leaking/low, check them all..... Cheap insurance. Once you have those numbers, a more accurate "guess" can be made. As for the valve lash...

To answer the until red flows, yes, but if it were me, I'd drain the tank completely and either "strain" the fuel, or dispose of it and start with fresh. Can't be coolant in the system if the system is empty.

"Stupid" idea, how hard/expensive would it be to set up a small compressor and air tank system like what's on the M series trucks? I can attest, it's nice having 90-120 psi on demand, just not familiar enough with the HMMWV to know if there's room under the hood and such......yet 😉

In my world "oilless" translates to "disposable", may just be me. After seeing that and reading the three star and lower reviews, I would say it's a pretty expensive gamble, especially pulling 90 amps, unless someone wrote the review for the wrong product.

https://maintenanceprocedures.tpub.com/TM-9-2815-210-34-2-1/TM-9-2815-210-34-2-10023.htm https://maintenanceprocedures.tpub.com/TM-9-2815-210-34-2-1/TM-9-2815-210-34-2-10024.htm These don't answer all the questions, but now we know the differences in injection timing, if we didn't already.

Ok..... I'm back from the rabbit hole. 37 pages later, and now we know for sure, the answer is yes, you can put LDS pistons in an LDT engine. You should put LDS pistons in an LDT engine because they are the same, or at least after a certain point they were the same. Same cam, crank, everything...

I wondered about that stuff forever, just waaay to skeptical to try it 😆. Definitely going to pick some up now knowing it works.

https://www.polaris.com/en-us/shop/off-road/maintenance/service-manuals/9927276/?pfm=search I'm sure they'll sell you whatever year you need, this is just what I found first, unless from 2017 on they're all the same, I don't know enough about them. Hope it helps

Any update on this? Sorry to pester you about it, super curious to see if it was the injectors after all.

TM 9-2320-361-10.