Search results

Has anyone ever used the left bracket on the right side as well? Hummerpartsguy is selling the right bracket for $250 but the left side bracket is $52. I understand why it would be expensive, but is it possible to install the left side bracket on the left as well? Any other places selling the...

I was looking at the 24p-1 manual and it shows how the relay and circuit breaker are mounted but not where. I would assume they would be in the battery compartment? I have the A2 harness so I need to know where they were meant to go.

Has anyone ever mounted a s-788 shelter in a m101a3 trailer? I know the s-250 ones fit, but I am looking for a little more space, and I found a website that is selling new s-788 for cheaper than the s-250. Plus the s-788 seems to weigh less (manufacturer website says s-250 weighs excess of...

Installed my A2 brake pedal switch today but the stroke of the pedal doesn't activate the switch. It appears that the switch only activates when it's half way through its total stroke but the actual pedal doesn't ever make it this far. I'm not sure what to do about this besides shortening the...

So if I have a post '97 4l80, can the old cooling lines be modified to (at least) reach the new plug locations? Both the 3l80 and 4l80 fittings look similar, but are they the same? If not, are there adapters that exist? And the 4l80e that I have does not appear to be quick connect, the plugs...

I was scrolling through google and I saw the image below. Whoever has that vehicle has used all three grooves in the 200 amp pulley. This leaves only one to drive the power steering? I've only put two on mine, and I don't see any problems, but I do have the a/c driven tachometer and it seems it...

Has anyone ever mounted a s-788 shelter in a m101a3 trailer? I know the s-250 ones fit, but I am looking for a little more space, and I found a website that is selling new s-788 for cheaper than the s-250. Plus the s-788 seems to weigh less (manufacturer website says s-250 weighs excess of...

I have two TCMs and I can't find anything about either one, can anyone identify what specific humvee model and transmission they were meant to go with? The data plate pictures are grouped together below, green tcm first then tan tcm second.

I looked at the TMs and their diagram with all the labeled connections doesn't include the numbered wires. I also looked on Google and there are a couple full diagrams for the harness's but they appear to be for either the old ambulances or a1 vehicles. Anyone know where to get the A2 wire...

I just put on a 4 man soft top and I was wondering if anyone knew of where to get a h1 bed cover (preferably locking). I've only seen one on epay and it's 1500 and has the pillars. I don't need the pillars, but are there any other brands that aren't expensive? Or should I just make one myself

So I was reading the mile marker installation manual for the humvee and it says that once all the wiring is in place that the controller is plugged into the connector right below the heater controls. But I checked the pins and they don't even remotely line up. Does this mean that connector is...

I was wondering what the difference was, electrical-wise, between the two. I've seen the two on epay and they appear to be mounted in a similar case, but I would like to know if the computers inside are identical. I am using the hummer h1 oil pump drive rpm sensor to feed my 4l80 with the...

I came across a post a while back about using a frag 5 door gaskets and modifying them and an x door to make them work together. From what the post said, it worked pretty well in weatherproofing a humvee. Since my only weather related issue lies solely in the leakage around my door seals, I want...

1. What is the little square radiator at the bottom of the radiator stack? Pics below 2. Just installed a new alternator, after I got the bracket in, I am pretty sure I tensioned the pump as much as I can. When the RPMs are above 2000, there is the squeaking sound of slipping belts. And when...

I read the instructions sent with it, and it says to reuse the nut from the 60 amp alternator, but I tried to fit that nut on and it was too small. 60 amp alt nut seemed to be 3/4 16 but the shaft on the 200 seems to be 7/8 in diameter. Anyone know the actual nut size? Also the pulley seems to...

I have recently installed a 200 amp alternator in my humvee in preparation for a 4l80 swap. In the instruction booklet, it says to ground the 14v tap. This makes no sense to me, so why do they do this? Also, if it is never hooked up to anything, what is the point of the dual voltage alternator?

So I've been going over the a2 body harness that I will be using with my 4l80 and it looks like I will need a 6.5 engine harness because of the connections to the engine rpm sensor and the TPS. Would a 6.5 NA engine harness work with a 6.2 engine?

I was doing some testing with the low lock on the transfer case and noticed something interesting. I was driving at low speeds with the t/c in high lock position, which means the front and rear axle are locked together, but when I went around a corner (for testing) the vehicle acted like the...

I am installing a 4l80 soon but I have a few clarifying questions before I begin. 1. Where is the TPS located? On the IP or the gas pedal? 2. If it's on the IP can the TPS be mounted on a 6.2l injector pump? 3. If it cannot or requires modifications is there a civi counterpart to the TPS that...

I know that there are plenty of other posts on the several different types of batteries and their respective advantages, but I wanted to ask the community what they suggest is the best. Currently I have some small car batteries sitting in my m999 right now, but only because the original 6tlmf...