• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

264Charlie's M51A2

2

264charlie

Member
Steel Soldiers Supporter
32
32
18
Location
Gainesville, TX
Hi all, I just picked up an unseen M51A2 from an auction site. It was a bit of an impulse purchase that resulted in about 50 hours of research, during which I'm much more educated about what I bought. I purchased the truck to move about 250 yards of dirt around my property. It should be a fun journey.

IMG_0989.jpg
 
2

264charlie

Member
Steel Soldiers Supporter
32
32
18
Location
Gainesville, TX
Does anyone have a recommendation for axles and brake rebuilt kit vendors? Or are the big ones that pop up on Google the best route to take?
 
Mullaney

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,716
19,766
113
Location
Charlotte NC
264charlie said:
I just got home and took a look at the M51. Well... the "All wheel drive. Starts, runs, drives and dumps well. This truck is ready to go" is a drastic over-exaggeration of reality. 50/50 If I'll part it out or get it going.
Click to expand...
.
That sounds pretty sad. I mean the paint job looks really nice. What about the internals? Are the Gear boxes, Motor, and Brakes okay? Or are at least some of the parts good?
 
fuzzytoaster

fuzzytoaster

Well-known member
Steel Soldiers Supporter
4,300
3,132
113
Location
Fort Worth, Texas
264charlie said:
I just got home and took a look at the M51. Well... the "All wheel drive. Starts, runs, drives and dumps well. This truck is ready to go" is a drastic over-exaggeration of reality. 50/50 If I'll part it out or get it going.
Click to expand...
Send it back and get your money back. They're all GSA Arkansas turn-in trucks..
 
NDT

NDT

Well-known member
Steel Soldiers Supporter
10,457
6,530
113
Location
Camp Wood/LC, TX
Dump trucks are always worth more assembled than in parts. Wow the picture you first posted sure did look good except for the ridiculous stenciling. They call that “lacquer overhaul” in the construction equipment biz.
 
2

264charlie

Member
Steel Soldiers Supporter
32
32
18
Location
Gainesville, TX
100% a lacquer overhaul with bad stenciling.

After much thought, I have a path forward. While it will be more expensive than I initially estimated, I am confident that the result will be something useful that I'm proud to own. When done, it's going to be a 25k—45k truck. I'm not sure I'd ever get that out of it, but I'm sure I could get .50 cents on the dollar.

Project goals:
- Trucking of gravel, dirt, trash, and scrap runs, 7 - 10 miles on back roads.
- Support a tag trailer to move the backhoe (around 8.5 Tons)
- Local pickup of heavy junk; I typically buy it within 150 miles
- A front Jin (a frame) poll would be a good idea for general use around the property if I could make it work with the dump.
- Just owing a 5-ton is fun, so I'll run with it, lol

Phase One: Functional, approximately $6K+ (I can fund this now)
- Axel Seals, bearings, and fluid changes. $1,500
-- I'm not sure I'll need bearings. I should do it if I have them apart, right?
- New Batteries plus install master shutoff switch $500
- Electrical 12v and 120AC in the cab $200
-- got to charge the phone and laptop
- Brakes $2,000
-- Replace/rebuild everything
- Dump cylinder rebuild & fluid changes $350
- Fuel system clean out, refresh $500 - $2,000
-- tanks, filters, lines, injection pump, injectors
- Fluids, filters, air system, services + misc issue that pop up $500+

Phase two, Comfort & Safety. Approximately $12K (If I sell my dump trailer, I can fund this)
- Shocks $900
- Electrical check, keyed ignition, lights, gauges, 12v trailer hookup, etc. $550+
- Weatherproofing. $2,500
-- Windows, seals, hard top
- Recovery $500
-- Tools, Tire repair, straps, jacks, and chains...
- Tires and wheels $3,500
--I will likely go with 395/85R20 because I like the looks, don't want 53s on a dump, and 14/20s don't seem as available.
- Seats $1100
- Center console, radio, comms, $500+
-Cab heat $500


Phase Three, Want list 19k+ (most likely will not get done anytime soon)
- Engine rebuild $2,500+
- 10 Speed trans swap & $2,000
- Rear lockers $2,500
- Paint $2,500
- Front winch, Jin Poll $3,500+
- Diff E-brake, maybe, it seems like it might be a good idea $500
- Air brakes $3,000
- Deep Water Kit $250
- Lighting and accessories $500+
- Locking Front Hubs $1,500





 
2

264charlie

Member
Steel Soldiers Supporter
32
32
18
Location
Gainesville, TX
Well, I flushed the primary tank and put in two new batteries, and the truck fired right up; the downside was that it had a fuel leak in the engine compartment, spraying fuel everywhere in a fine mist. At this point, I figured out that the truck did not have a primary or emergency engine stop. I tried capping the intake with no luck, so I cut the fuel line. Fun times.

I hope to fix the fuel line this weekend and make a plan for the fuel cutoffs. I started looking through manuals to find out how they should be run, but I haven't found the answer yet.

I should have just stalled the engine. Dang it. Hindsight.
 
Last edited:
2

264charlie

Member
Steel Soldiers Supporter
32
32
18
Location
Gainesville, TX
NDT said:
Your truck has a multfuel engine essentially the same as “deuce” trucks. The engine shut off system has probably dozens of threads on here as it causes issues.
Click to expand...
Yep, I'm aware. Mine is missing the levers in the cab, so I am looking to see how they were initially run to the pump.
 
Valley Rock

Valley Rock

Big wheeler cat peeler
Steel Soldiers Supporter
445
836
93
Location
Orygun
These old trucks always need work, whats so bad about it ?

4k to your door seems like a decent deal to me, at least its a 5 ton .
 
You must log in or register to reply here.
110,879members
165,311threads
2,326,198posts
2,051online users
Top