Finally !! scored a hmmwv m998, LOTS to learn !! let the fun begin !!

[Retiredwarhorses]

Correct for that pump is
0432217092....0430211054...NA51X...0SD253....126 bar......6.2L Short body

but that depends on your heads....but I assume you got your reference from an exsisting injector.
so, put those in...and a new pump.

 

[Stonepicker1]

Standyne Injectors (New)
37818 10233973 6.5L T.D.

This is what I installed in two of my CUCV-II's(6.5L Turbo).


Standyne Injectors (New)
38272 10233972 6.5L N.A. same as 0432217275 6703802

This is what I installed in one of my CUCV's(6.2L).

All injectors were new and have not had a problem with them.

 

[auctionaddict]

Block # 660 so its a 6.2

 

[Retiredwarhorses]

A 6.2 has it in the casting on the front pass side near the water pump...also, no crank position sensor hole
on driver side down near the harmonic balancer....

 

[auctionaddict]

Still not running, but close I hope !!
All I need are the injectors that should be here tomorrow !

Here is what I have done so far,

Rebuild pump
Rebuilt injectors
Rebuilt radiator
New fuel pump
New ground upgrade
New water pump
New fan clutch
New glow plugs
New smart start system
New batteries
New belts
New hoses
New filters (all)
New tires (stolen from my 1101s)
New 4 man soft top kit
New skid plate kit
New hub seal kits
New dash and gauges
4 new Mastercraft MRAP seats with harnesses
SW CARC paint (not painted yet)
Led headlights
Led master switch
Led tail lights with cameras
Led turn and marker lights

Also picked up a Complete slantback kit with x doors
Working on custom safari doors



To late to turn back now !!!

Got to have her ready for GA rally !!




My fuel filter !

 

[Pablo66]

Still not running, but close I hope !!
All I need are the injectors that should be here tomorrow !

Here is what I have done so far,

Rebuild pump
Rebuilt injectors
Rebuilt radiator
New fuel pump
New ground upgrade
New water pump
New fan clutch
New glow plugs
New smart start system
New batteries
New belts
New hoses
New filters (all)
New tires (stolen from my 1101s)
New 4 man soft top kit
New skid plate kit
New hub seal kits
New dash and gauges
4 new Mastercraft MRAP seats with harnesses
SW CARC paint (not painted yet)
Led headlights
Led master switch
Led tail lights with cameras
Led turn and marker lights

Also picked up a Complete slantback kit with x doors
Working on custom safari doors



To late to turn back now !!!

Got to have her ready for GA rally !!


View attachment 514903

My fuel filter !

View attachment 514904

Loving those Safari doors! Are you planning on mass producing them??!
I've been working on a 1987 M1038, but your project seems to be moving along much faster than mine!

 

[Augi]

Be careful with the MRAP seatbelts. The floor of the HMMWV isn't really strong enough to hold the combined force of a person and the seat (especially in the rear, where it's just a couple of clips retaining the seat pan) and you can rip the whole seat out with you still strapped in during a collision.

Augi

 

[Retiredwarhorses]

Augi has a good point, the HMMWV seat belt system is anchored into the body with backing plates.
the seat on the battery box and rear seats could be torn out with just pulling hard enough on them.
the battery box cover is only made of fiberglass....personally I wouldn't run them for safety sake.

 

[EwaMarine]

Make some brackets to safen it up a bit more!! Youll figure it out!!

 

[auctionaddict]

I used the factory mounting points on the sides and braced for the rear mounts !!

 

[Donnie]

Working on custom safari doors



View attachment 514903

]

They look great!

 

[R Racing]

Any updates? We're you able to get it running?

 

[Jayson]

Its been about 8 months, are the injectors still in the mail?

 

[auctionaddict]

No, She is going great now ! Been on an extended test ride, Haven't had time to post

Its been about 8 months, are the injectors still in the mail?