-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
FLU419 SEE HMMH HME Owners group
- Thread starter Migginsbros
- Start date
brandan34
Member
- 45
- 37
- 18
- Location
- Southern Oregon
Has anyone replaced the boots on the axle shafts? I have one of the axles loose and I am now stuck. I do not see anyway to get the one piece boot that the military used over the ball on the axle tube and into place. Is this a case where I get some tire changing spoons and force it or is there a trick? I have not find where this is changed in the manual, every other part of the tube and tranny, but not what they call the bellows.
peakbagger
Well-known member
- 734
- 360
- 63
- Location
- northern nh
I have not done the repair but I have seen references to people using split boots for replacements. The original does not have a seam. The replacements have molded seam that is held together with hardware and sealed with silicone. https://www.ebay.com/itm/2750272562...85073288&device=c&mktype=pla&googleloc=900238
Last edited:
brandan34
Member
- 45
- 37
- 18
- Location
- Southern Oregon
I am starting to see why they do that. If you use the split kind it does not have a spot for the airhose when you turn on the 4x4 and there was another reason that i forget now that ei thought like orginal was better. I do have a help ticket in with them. At this point i do not see it an obvious way other than force.
peakbagger
Well-known member
- 734
- 360
- 63
- Location
- northern nh
Unless you plan to be "fordng" with your SEE, its best to disconnect the pressurization system. Its fed low pressure air from a pressure regulator that if it fails, supplies full pressure to the system and will blow out the seals on the portals.
brandan34
Member
- 45
- 37
- 18
- Location
- Southern Oregon
That is what i have read and probably will, though it is nice to have options and there are places i could see wanting to go that those parts would be under water for a few minutes.
peakbagger
Well-known member
- 734
- 360
- 63
- Location
- northern nh
There is big experience base on Benzworld on the 400 series models and the same axles were used on the SBU series. it would be worth doing some searching on how others do it.
brandan34
Member
- 45
- 37
- 18
- Location
- Southern Oregon
That is what i have read and probably will, though it is nice to have options and there are places i could see wanting to go that those parts would be under water for a few minutes
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
If so, put a valve in the line so you can turn the air on when/if you want to pressurize the axles.
peakbagger
Well-known member
- 734
- 360
- 63
- Location
- northern nh
I think the problem is, if the new boot does not have an air connection, then the turning on the valve is not going to make a difference. I guess I need to crawl under my SEE once the snow melts as I did not know there was an air connection on the boot
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
That makes two of us.I guess I need to crawl under my SEE once the snow melts as I did not know there was an air connection on the boot
peakbagger
Well-known member
- 734
- 360
- 63
- Location
- northern nh
When I look in the part manual, the illustration does not show an air line connected to it.
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
As I recall, the line comes from the top of the axle housing, then the rubber portion goes to the backing plate. Much like a typical brake hose.
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
Today I wanted to use the SEE that gave me all kinds of grief (fuel system, primarily) when I first got it.
After it sitting for maybe three months, including in -22 temps, I didn't really know what to expect. Well, it started up instantly - once I remembered that I have to push in the switch on the clutch by hand on that one.
That the temp gauge didn't seem to work didn't bother me. Or that it eventually went up to quite high, then down to normal. The wipers didn't work, either.
So what? These Unimogs are great.
After it sitting for maybe three months, including in -22 temps, I didn't really know what to expect. Well, it started up instantly - once I remembered that I have to push in the switch on the clutch by hand on that one.
That the temp gauge didn't seem to work didn't bother me. Or that it eventually went up to quite high, then down to normal. The wipers didn't work, either.
So what? These Unimogs are great.
Another Ahab
Well-known member
- 17,989
- 4,532
- 113
- Location
- Alexandria, VA
Attachments
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
Thinking more about it, I'm no sure I've ever tried the wipers before.
Another Ahab
Well-known member
- 17,989
- 4,532
- 113
- Location
- Alexandria, VA
MogPoggers
Member
- 45
- 95
- 18
- Location
- Jamestown, New York
You guys may have seen a camo FLU419 with ripper bucket and new Pirelli Pista 22 tires for sale in Marengo, Ohio recently... and you may have noticed that the Ebay listing is no longer active. That's my doing. A deal has been struck and I will be in your exclusive little club very soon
I'm currently working my way through all 270 pages of this thread, along with the operator and technical manuals. See you in a couple months.
I'm currently working my way through all 270 pages of this thread, along with the operator and technical manuals. See you in a couple months.
MogPoggers
Member
- 45
- 95
- 18
- Location
- Jamestown, New York
Does anyone have thoughts on a rear PTO? Beyond it's normal uses, I want to use the FLU to run a haybine, tedder and hay baler. I'm not sure how accessible the existing rear PTO is, even with the backhoe removed - but even if that's feasible, I'd rather not do it. I will be using the hoe often, so I'd like to leave it attached.
I was thinking I might weld an attachment point for a hydraulic PTO to the bottom of the backhoe, above the pintle hitch and then tap into the tool/extension hydraulic system and run lines back to it so I can use the PTO while the backhoe is in the stowed position.
I was thinking I might weld an attachment point for a hydraulic PTO to the bottom of the backhoe, above the pintle hitch and then tap into the tool/extension hydraulic system and run lines back to it so I can use the PTO while the backhoe is in the stowed position.
Last edited:
- 3,338
- 1,319
- 113
- Location
- The actual midwest, NM.
You won't be able to run anything meaningful off the front hydraulics.
I ran a snowblower off of the rear hydraulics for a few years, but if I did it again I'd put valves in the circuits instead of having to switch the quick disconnects for the backhoe twice a year.
I ran a snowblower off of the rear hydraulics for a few years, but if I did it again I'd put valves in the circuits instead of having to switch the quick disconnects for the backhoe twice a year.