kennys@wi.rr.com
Active member
- 1,472
- 23
- 38
- Location
- Waukesha, WI
If the IP is 180 out of phase the motor will still start and run. But it will be rough and hardly idle unless you are on the throttle.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Hey Need help with a IP head part
- Thread starter highfavor1004
- Start date
- 3,021
- 221
- 63
- Location
- eldersburg maryland
360 out is the same as 0 out, so yes it would run fine
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
Yup, what Tom said(Kenny too).
RAYZER
Well-known member
- 3,380
- 59
- 48
- Location
- sanford/florida
Ha! That was a test and you guys passed!
- 456
- 0
- 16
- Location
- Eustis, Florida
Hey guys I have located the problem. the fuel coming out the breather tube is the is coming from the fuel dumping into my crank case from the IP. I brought the gasket kit for the IP; however i know of two o-rings pm the head and have been told another is on fuel shut off. The two question that I have is 1. Are these the only three points that it could be leaking (this problem was not happening before i took off the head). 2. Does any one have a diagram that i can fallow on how to replace the o-ring for the fuel shut off?
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
Yes, there is a third O-ring on the fuel shut off rod. I might be able to find the size, hang on a sec. Is your FDC in the fuel line or is it bypassed? The FDC is known for leaking fuel into the crank case too.
- 456
- 0
- 16
- Location
- Eustis, Florida
it is bypassed
kennys@wi.rr.com
Active member
- 1,472
- 23
- 38
- Location
- Waukesha, WI
I still have all three o rings available.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
I couldn't find the small one's size, do you have it Kenny?
kennys@wi.rr.com
Active member
- 1,472
- 23
- 38
- Location
- Waukesha, WI
I have all three of them available. Sizes are 013, 227 and 230. PM sent to OP.
- 456
- 0
- 16
- Location
- Eustis, Florida
Yea I have already brought the complete set of gaskets for the IP. But theses are the o-rings we are talking about correct?
Attachments
- 456
- 0
- 16
- Location
- Eustis, Florida
you cant see were i mark in those he is a better picture
Attachments
kennys@wi.rr.com
Active member
- 1,472
- 23
- 38
- Location
- Waukesha, WI
Yes.
- 456
- 0
- 16
- Location
- Eustis, Florida
so those are the only three points that it can leek into the crank case correct?
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
Wait a sec, yous second pick is not right highfavor.
Kenny, did you see what he is pointing at?
Kenny, did you see what he is pointing at?
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
Neither the first pic nor the second has the right part shown for the small Oring.
- 3,021
- 221
- 63
- Location
- eldersburg maryland
fuel coming out the engine breather??? it's on top of the engine, so the crankcase and engine would have to be full!!!
remove the shut off cover and just turn on the tank pump. do you have a LARGE amount of fuel there? if yes, o ring bad or missing. if no the seal on the booster pump is the culprit. they can leak a huge amount of feul.
tom
remove the shut off cover and just turn on the tank pump. do you have a LARGE amount of fuel there? if yes, o ring bad or missing. if no the seal on the booster pump is the culprit. they can leak a huge amount of feul.
tom
- 456
- 0
- 16
- Location
- Eustis, Florida
okay thank you so much
- 456
- 0
- 16
- Location
- Eustis, Florida
wait were is the booster pump located
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 752
- 113
- Location
- Cincy Ohio
I forgot about the booster pump seal too.