- 275
- 3
- 18
- Location
- pefferlaw ontario
as per GM the relay must have a minimum 120 amp rating when installing the 28MT,
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M1010 somebody talk me down
- Thread starter riggermedic
- Start date
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
I have an M1010 that I am currently gutting and would like to solicit some opinions on insulation.
I have been buying a lot from an auction in vegas to transform this into an RV.
I bought this cabinet to serve as clothes and food storage. I like the flip up top for a countertop and cook surface for a propane camp stove.
I bought a field portable scrub sink to use as a sink… obviously
I scored 5 field deployable hospital beds with mattresses and plan on trying my hand at some fold down bunk beds along the side.
But back to the original question on insulation. This truck has been hacked by a search and rescue group so I began by stripping out all the old rat eaten bug infested insulation and of course drilling the 9,965 rivets attaching the inner skin. A complete rewire will be needed.
I originally thought of spray foam insulation, but am hesitant as I have never used it and seems to be a less modifiable choice if I need to add wiring or plumbing at a later date. I considered dynamat, but that is awfully pricy.
Then I stumbled onto 26 panels of vehicular thermal insulation made by general dynamics. It is a 4 foot by 4 foot panel of aluminum covered foam with a peel and stick adhesive backing.
I think this will work for the outermost layer against the inside of the skin of the ambulance box.
I don’t think it would benefit by stacking multiple layers of this? any thoughts or opinions?
I am also open to a foam board type insulation but have not really priced this option out.
Another thought in keeping with the all military theme is to stack some old PT mats (sleeping mats) and making my own foam boards from these. Any thoughts/ opinions?
I have been buying a lot from an auction in vegas to transform this into an RV.
I bought this cabinet to serve as clothes and food storage. I like the flip up top for a countertop and cook surface for a propane camp stove.
I bought a field portable scrub sink to use as a sink… obviously
I scored 5 field deployable hospital beds with mattresses and plan on trying my hand at some fold down bunk beds along the side.
But back to the original question on insulation. This truck has been hacked by a search and rescue group so I began by stripping out all the old rat eaten bug infested insulation and of course drilling the 9,965 rivets attaching the inner skin. A complete rewire will be needed.
I originally thought of spray foam insulation, but am hesitant as I have never used it and seems to be a less modifiable choice if I need to add wiring or plumbing at a later date. I considered dynamat, but that is awfully pricy.
Then I stumbled onto 26 panels of vehicular thermal insulation made by general dynamics. It is a 4 foot by 4 foot panel of aluminum covered foam with a peel and stick adhesive backing.
I think this will work for the outermost layer against the inside of the skin of the ambulance box.
I don’t think it would benefit by stacking multiple layers of this? any thoughts or opinions?
I am also open to a foam board type insulation but have not really priced this option out.
Another thought in keeping with the all military theme is to stack some old PT mats (sleeping mats) and making my own foam boards from these. Any thoughts/ opinions?
joshuak
Active member
- 747
- 215
- 43
- Location
- Slower shore, DE
Good scores on your equipment!
I used polyisocyanurate foam board from HD, here. Covering the ribs or studs is important IMO, they'll allow undersired for heat transfer even if you fill the space between them.
Build thread.
I used polyisocyanurate foam board from HD, here. Covering the ribs or studs is important IMO, they'll allow undersired for heat transfer even if you fill the space between them.
Build thread.
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
that is a very nice thread you got going
chevymike
Well-known member
- 604
- 471
- 63
- Location
- San Diego, CA
Sweet! I am loving that cabinet you picked up.
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
Gutted the interior
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
More pics
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
And more
riggermedic
Active member
- 175
- 31
- 28
- Location
- Phoenix AZ
Video
Video rear hinges
failed upload
Video rear hinges
failed upload
Last edited:
chevymike
Well-known member
- 604
- 471
- 63
- Location
- San Diego, CA
Man that is looking great. This is what I am needing to do on mine but want to strip mine down when I am a little closer to actually building out the back.