• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

M925a2 Power Surge

74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
Well, the engine cranks well and ECM seems to actuate, but so far no fire. It will light off on starting fluid, but not self sustain. The engine has an electric boost pump on it, but it is inline style, and those are never lift capable, just pressure boosters once flooded with liquid. Trucks these come from still have hand prime pumps on them, I think. Right now I have 4 fuel lines in a gallon jug of diesel about a foot below the engine. It seems to be one delivery and 3 return hoses. They are all 4 below the diesel fluid level surface in the jug. But with only running the electric pump on the engine, I don't think it can lift fuel.

I cracked open one of the common rail injector feed lines, and little to no fuel came out when cranking. For something that should have nearly 20,000psi on it, I expected more than that. So far, I think it is a fuel delivery issue just with the test setup I have. I am going to add a small electric lift pump or outboard hand squeeze bulb on the inlet line, and try again. If still no fire, then will hook a diagnostic tool to it. We have Cummins diag software with the testing we do here. I think I need a manual primer pump on it to push fuel to the electric boost pump.

Engine fuel lines are 2 large ones off the back of the block labeled with one inlet and outlet arrow and then 2 small cloth braided ones coming from the high pressure common rail pump, one off the lower portion and one off the upper higher pressure part. I assume to be for cooling of the pump. Regardless, I have them all submerged in a gallon of diesel, but below the engine (can on ground, engine on trailer). So, lift or primer pump on the single larger 3/8" fuel line is the next shot.

At least mechanically she sounds and seems OK, so far. Who knows, maybe the crank sensor was bumped during removal and is wiped out, etc.... Scan tool should show this if the case, which will be next step if manual ly pressurizing fuel into the inlet line does nothing.

That's all for now, back to work, will try next step tonight after kids are in bed.
 
Another Ahab

Another Ahab

Well-known member
17,995
4,546
113
Location
Alexandria, VA
74M35A2 said:
At least mechanically she sounds and seems OK, so far. Who knows, maybe the crank sensor was bumped during removal and is wiped out, etc.... Scan tool should show this if the case, which will be next step if manual ly pressurizing fuel into the inlet line does nothing.
Click to expand...
Are all scanners more or less "created equal"?

Or are there one or more models that are most preferred over others?
 
Last edited:
74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
Just tried again, cracked the line from the common rail pump which feeds the common rail, and no fuel coming out. Hopefully this is just an air bound issue. I will disco the line after the boost pump and see if it will flow when the pump is on. The ECM is mounted to a plate which the diesel flows through to cool the ECM.

Just checked, no primer pump on either fuel filter which I removed from the RV. Hmmm.
 
Last edited:
74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
Got it! Will's the man. He taught me that there should be two filters on the RV, and there was, and that fuel feed to the high pressure pump should be double filtered, and at about 70psi. This was not making sense to me, because I know the lift pump does not generate that kind of pressure. After looking at the hose type on the smaller filter housing and him saying it should have high pressure banjo fittings, I see that this filter has the same braided cotton hose on it that comes from 2 areas of my common rail pump. Well, I have both those lines stuffed into the jug, thinking they are both returns, and instead they are supposed to be joined together, with the higher pressure filter in between. So, I was simply recirculating fuel from the lift pump and low pressure pump side of the HPCR pump, and not supplying any to the upper section of the high pressure common rail fuel pump. Result? No fuel, as I was seeing.

I need to get a banjo ended test line made up for the actual start, but at least this is solved and SHOULD be the only no-start reason. As always, stay tuned...
 
Last edited:
snowtrac nome

snowtrac nome

Well-known member
1,674
139
63
Location
western alaska
this is an air issue just went through this with some 300 hp mrap engines, the priming pump would be a good way to get fuel to the fuel pump, which also is supposed to be your lift pump the booster just helps it along cummins uses banjo fittings with a strange metric thread on the bolts
 
74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
It was a mis-plumb issue in this case since everything was cut out vs disco'd. Confirmation later this evening, I need a small high pressure banjo ended hose made before she will fire, but the parts guy at the hydraulic hose store is in standby with my order, waiting to deliver it.
 
Last edited:
74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
IT RUNS !!!!! PERFECTLY! Zero leaks, zero smoke, 400hp, ready for its next assignment. Run for your life Simp! Cats are out of the bag.

Thanks to all for the help and encouragement.
 
Last edited:
T

TedCat

Member
Steel Soldiers Supporter
58
3
8
Location
Saline Mi
VROOM VROOM VROOM VROOM... CLICK PSST... VROMMMMM VROOMMMMM VROOOOOOMMMMMMM VROMMMMMMMMMM...
(Granny plus 4 split 4 more!)
 
snowtrac nome

snowtrac nome

Well-known member
1,674
139
63
Location
western alaska
same thing I had with the m rap engines I was working on we made our own fittings but had to buy the new bolts some one had discarded the bolts and fittings and tried to use brass hose nipples. insite picked it up real fast that there was air in the system.
 
74M35A2

74M35A2

Well-known member
4,145
330
83
Location
Livonia, MI
Next step is to rip this Allison off and connect the Road Ranger to it with the new clutch, may harvest the flywheel housing from my mil engine, TBD yet, based on motor mount comparison. This one has driver side starter, which may be OK, need to check clearance. Oil pan will need to flip around to front sump, will need to acquire a front sump pickup tube. Will buy new to keep my stock engine complete to sell.
 
simp5782

simp5782

Feo, Fuerte y Formal
Supporting Vendor
12,123
9,368
113
Location
Mason, TN
74M35A2 said:
IT RUNS !!!!! PERFECTLY! Zero leaks, zero smoke, 400hp, ready for its next assignment. Run for your life Simp! Cats are out of the bag.

Thanks to all for the help and encouragement.
Click to expand...
You think an old 855, even though its a small cam, is suppose to be scared of a tug of war vs something that powers your grandpappy's Winnebago?

Clint in winter.

https://youtu.be/9PB349Z4XEA

Sent from my SM-G935P using Tapatalk
 
Last edited:
You must log in or register to reply here.
110,793members
165,250threads
2,325,091posts
1,298online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks