JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
My fuel gauge started flickering back and forth all over the place. Now later on ust pegged far as it will go past full and staying there. Fuel gauge gone bad? Thanks for any info on what to do.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Mep 802 A fuel gauge
- Thread starter JimmyLet58
- Start date
- 3,836
- 5,964
- 113
- Location
- MA
You can check the sender, but in my experience when its pegged far right its a dead gauge. If you are looking for a replacement, I have them listed in the classified section.
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
Thanks for the info. Where is the classified section you have the qauge listed?
- 3,836
- 5,964
- 113
- Location
- MA
Just send me a direct message and we can discuss the gauge. But you can view the listing here: https://www.steelsoldiers.com/threa...3-beede-945331-6625-01-366-0193-70-ea.199406/
Thanks
Thanks
Zed254
Well-known member
- 866
- 466
- 63
- Location
- S. Hampton Roads, VA
https://armysurpluswarehouse.com/military-issue-fuel-gauge/ might work for you. I used one on my 802. It's not OEM black, but it is a Teleflex gauge and good quality. UPS from Idaho can be expensive, though. I bought a few spares and included them in a larger order to neutralize shipping cost.
Attachments
- 2,532
- 2,060
- 113
- Location
- Efland, NC
If the gauge is jumping around it could be a dirty sending unit. You can pull it out of the tank and clean it with carb cleaner. I've recently had to do that to one.
Ray70
Well-known member
- 2,598
- 5,931
- 113
- Location
- West greenwich/RI
Definitely test your sending unit. A dead spot in the sender will also peg the gage all the way up. The dead spots can also be intermittent, so check closely.
Make sure you disconnect the sense wire from that gage before testing it otherwise you will get an incorrect reading.
I would just replace it with a marine sending unit for $30.
There are plenty of articles on her about the WEMA SS units as well as others.
For an 802 I believe you need a 5.5" sender and you want the standard SAE mounting hole pattern, IF you end up having a bad sender.
Make sure you disconnect the sense wire from that gage before testing it otherwise you will get an incorrect reading.
I would just replace it with a marine sending unit for $30.
There are plenty of articles on her about the WEMA SS units as well as others.
For an 802 I believe you need a 5.5" sender and you want the standard SAE mounting hole pattern, IF you end up having a bad sender.
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
Zed254
I got the gage I am not sure I got it hooked up right. Do you have a picture of how you have yours wired. When I put power to mine the needle pegs to the left pasts empty!
Thanks Jimmy
jmenende
Well-known member
- 467
- 389
- 63
- Location
- Puerto Rico
I would sand and clean with some contact cleaner all the terminals on the gauge. Also, take the back cover off and clean the contacts off the sender. While you at it, stick your hand inside the fuel take and make sure both float are free and move up and down. This last part may be difficult for some with giant hands and you may end up pulling the sender.
Ray70
Well-known member
- 2,598
- 5,931
- 113
- Location
- West greenwich/RI
Jimmy, where are you at with this machine as of now? Have you gotten the gage wires figured out, or do you still need help?
Also, have you tested the sending unit in the tank? I can almost guarantee your sending unit is bad. I've seen it a dozen times.
It's easy to test, just disconnect the wire on the 3/8" nut on the sending unit and use and ohm meter to check resistance from the stud on the sending unit to ground. Open circuit means sender is bad. Maybe it can be cleaned, but experience has told me to just replace with the marine stainless steel unit, it will save you 100 headaches. There is another thread started just recently regarding this same issue that you may have seen...
Also, have you tested the sending unit in the tank? I can almost guarantee your sending unit is bad. I've seen it a dozen times.
It's easy to test, just disconnect the wire on the 3/8" nut on the sending unit and use and ohm meter to check resistance from the stud on the sending unit to ground. Open circuit means sender is bad. Maybe it can be cleaned, but experience has told me to just replace with the marine stainless steel unit, it will save you 100 headaches. There is another thread started just recently regarding this same issue that you may have seen...
mep-802a fuel level sender float
my fuel gauge read "E" so I followed the TM and pulled the sending unit and it Ohm'd out to specs. I reinstalled it and ordered a new fuel gauge. I get the new gauge installed and it's and still on "E". I next ohm'd it in place with a full tank and it's reading 216 ohms = near empty. I made...
www.steelsoldiers.com
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
Ray thanks for all your itime and Information. I haven't had time to check everything out yet. Just getting ready to order the marine stainless unit. So I need the 5.5 for the 802 correct?
Ray70
Well-known member
- 2,598
- 5,931
- 113
- Location
- West greenwich/RI
Yes. 5.5" is the correct length for an 802. a 5" will work, but fuel level will be off a tad. Gage will say empty when you have like 1/8 or less left, not a big deal either way.
Zed254
Well-known member
- 866
- 466
- 63
- Location
- S. Hampton Roads, VA
My 802 is located at some property I own several hours away, so I cannot take a picture of the wiring. I've attached a Beede Gauge Testing document that shows the 3 wires on a fuel gauge: Sender, Ground, Ignition. The back of the fuel gauge has the S, G, I molded next to the terminals. I've also attached a picture of my 803 fuel gauge wiring. The black wire is non-standard illumination for the gauge and won't be on yours.
Attachments
Ray70
Well-known member
- 2,598
- 5,931
- 113
- Location
- West greenwich/RI
FYI be warned that the newer white body white Beede gages and the older Blue body gages ( not sure who made those ) are wired differently.
Or I should say the terminals are on opposite sides of the gage.
All you need to do is pay attention to the markings on the back of the gage.
The I terminal is for 24v+ the G is ground and S is the sense wire going to the sending unit.
All gages are marked with the same identifiers, just match them up. If you removed the wires and aren't sure where they came from simply use a DMM to look for voltage to find your power and ground, or use the ohm's setting to test the wires compared to one of the other gages.
Or I should say the terminals are on opposite sides of the gage.
All you need to do is pay attention to the markings on the back of the gage.
The I terminal is for 24v+ the G is ground and S is the sense wire going to the sending unit.
All gages are marked with the same identifiers, just match them up. If you removed the wires and aren't sure where they came from simply use a DMM to look for voltage to find your power and ground, or use the ohm's setting to test the wires compared to one of the other gages.
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
Thanks for all your help Ray!
Jimmy
JimmyLet58
New member
- 15
- 10
- 3
- Location
- NC
Hi Ray how many qts of oil does the 802 hold with the filter?
I see on the front cover says 3.2 is the with the filter full?
Thank you Jimmy
You been such a big help!
Ray70
Well-known member
- 2,598
- 5,931
- 113
- Location
- West greenwich/RI
It holds just enough to read full on the dipstick! 
Actually you are in the ballpark at about 3 - 3 1/2 qts, but I always fill from the larger 2 1/2 gallon jugs so I just keep adding till dipstick is satisfied and never paid much attention to how much it holds, especially since you don't really get it all out due to the drain being on the side.
Actually you are in the ballpark at about 3 - 3 1/2 qts, but I always fill from the larger 2 1/2 gallon jugs so I just keep adding till dipstick is satisfied and never paid much attention to how much it holds, especially since you don't really get it all out due to the drain being on the side.