- 530
- 836
- 93
- Location
- Texas Hill Country
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Need a wire diagram for a m1078 a1. 2001. Transmission schematic.
- Thread starter Xengineguy
- Start date
Ronmar
Well-known member
- 3,825
- 7,427
- 113
- Location
- Port angeles wa
Looking over the first part of your new .PDF, Revision J Vehicle S/N18549 & below, the only thing I am seeing is it appears to have kept the A0 charging system, Alt and PPD, no LBCD and no remote or manual disconnects. This agrees with my experience helping a few with early A1 power issues that had those same “features”
Ronmar
Well-known member
- 3,825
- 7,427
- 113
- Location
- Port angeles wa
Yep, its not listed in the equipment reference lists in either of those documents, but R13 and its P250 connector is shown in the drawings in both those .PDFs on page 20… That is one thing I don’t like about these A1 drawings, the equipment ref doesn’t list the connector locations either like they did in the A0 drawings. Not very friendly when you are trying to identify things, like “what the heck is this grey thing”
- 530
- 836
- 93
- Location
- Texas Hill Country
Yes, not in the index, though on the J1939/1587 bus page in both. Once again I bow to you Ronmar.
It shouldn't be added to the TM's, my mistake. Let us remove it—
Ronmar
Well-known member
- 3,825
- 7,427
- 113
- Location
- Port angeles wa
No, i think that J version is good info to have available. There may be some other differences that we might not know about until we actually try to reference something specific.
- 816
- 1,491
- 93
- Location
- Mesa Colorado
Senior moment:
a year+ ago, before I had these new A1 schematics, I spliced into wires 1925 and 3020NN based on the TM diagrams which don't match this. I didn't use the splice so it's just taped off. I'm pretty sure this unused connector is the "options panel" connector which I don't have. 1925 powers up to 25v in ignition on. 3020 references TB2. Problem is, I can't find 1925 anywhere in the schematics nor can I find the J913 shown. So I'm not quite sure what I've tapped into, exactly. Trying to find a good 24v ignition source for my gps speedo.
a year+ ago, before I had these new A1 schematics, I spliced into wires 1925 and 3020NN based on the TM diagrams which don't match this. I didn't use the splice so it's just taped off. I'm pretty sure this unused connector is the "options panel" connector which I don't have. 1925 powers up to 25v in ignition on. 3020 references TB2. Problem is, I can't find 1925 anywhere in the schematics nor can I find the J913 shown. So I'm not quite sure what I've tapped into, exactly. Trying to find a good 24v ignition source for my gps speedo.
- 530
- 836
- 93
- Location
- Texas Hill Country
J913 on page 10 B/C 3/4 area.
Wires 1904 page 4/58 connects to trans ecu PTO sensor, PTO on/off and CB49 off X3 at the PDP; and and 2019 goes through P913 to K37 (PTO) on page 4 C 2/3 area.
That may support the options panel idea—
Last edited:
- 816
- 1,491
- 93
- Location
- Mesa Colorado
Ok I'm seeing that. I remember now that I was trying to pull Power off the pto feed bc I don't have a pto. 1925 is shown in the TMs as PTO related, but not shown on the fmtvA1 diagrams. Seems like a workable concept since that J913 is unused. Lots of wires in that console. I can see now why the Canbus is so popular.
- 530
- 836
- 93
- Location
- Texas Hill Country
1925 is on page 4/59 it is between CB49and the PTO on/off switch, 1904 is on the otherside of the switch—
- 816
- 1,491
- 93
- Location
- Mesa Colorado
AHHHH! how did you find that? That's great man! I've been scanning those pages for days looking for that friggin wire. So it IS the same as the TM at least for that circuit. That makes me feel good
. Exactly as I planned lol . I didn't want to mod any of the existing speedom connector wiring in case I convert back.