BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Oh yeah. Unique defiantly I'm worried that the 5.9 will be a little to loud in the cab I might have to build a custom muffler. I guess I'll see Wednesday when my 90 degree elbows come in ups.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Rat Deuce project 1
- Thread starter BBQROD
- Start date
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Finally some progress on Frank N Deuce. Twins!
Don't worry there not going to stay that tall.
Don't worry there not going to stay that tall.
Last edited:
RAYZER
Well-known member
- 3,380
- 59
- 48
- Location
- sanford/florida
Very cool!
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Custom brackets 
rebelqwes87
New member
- 179
- 0
- 0
- Location
- Loganville, Ga
This thing is sweet!!
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Well I have got a few more things completed. I cut the exhaust down to a reasonable height. I put the rear window panel in and cut out a few window seal plates.
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Well today me and Frankin Deuce went on a 130 mile test drive. I purchased a pair of super single 22.5 tires and now I have got two find two rims for them. 
Everything went well on the trip but the primary fuel filter got partially stopped up so I see a fuel tank flush in the near future!
Everything went well on the trip but the primary fuel filter got partially stopped up so I see a fuel tank flush in the near future!
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
And I forgot about my home made exhaust fender flanges 
- 14,640
- 4,820
- 113
- Location
- Buchanan, GA
Wanna take on some more sheetmetal work after this?
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
I don't know how much more I can do without buying a press but I'm saving all the files for repeated use.
wilber
Member
- 149
- 24
- 18
- Location
- olathe kansas
I just wanted to say thanks for the cool thread.
- 14,640
- 4,820
- 113
- Location
- Buchanan, GA
It'd all be flat sheetmetal. Think HMMWV. I have a couple hundred page book with the prints for everything.
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Sounds like fun just shoot me something via email (PDF or what ever) and I'll give it a shot.
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Well I worked out a trip to the liberty truck and tractor pull Saturday night averaged 60 mph on a bus tuneup only issue was a drive shaft vibration other than that it purred like a kitten. Well one that likes to whistle at least.
Last edited:
o1951
Active member
- 899
- 155
- 43
- Location
- Bergen County, NJ
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Got some coming soon fixing to start paint and some cosmetic work.
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Oh no I have some drive shaft woes! I'm having a phasing or angle issue. New joints good support bearing. Doing a little research and fact finding to figure out what's going on.
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
I found some steel super single rims today! Ole Frankin deuce gets some new sneakers tomorrow! 
BBQROD
New member
- 255
- -13
- 0
- Location
- Gray Georgia
Whee Hoo! I'm so excited I finally got to install my super single mud grippers today. Ole rat truck is starting to shape up. 
