rustystud
Well-known member
- 9,280
- 2,988
- 113
- Location
- Woodinville, Washington
I finally installed my fuel safety shut-off valve. This is for "just in case" when I'm messing with the injection pump settings. Don't want any run away engines here.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Safety fuel shut-off
- Thread starter rustystud
- Start date
I finally installed my fuel safety shut-off valve. This is for "just in case" when I'm messing with the injection pump settings. Don't want any run away engines here.
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 755
- 113
- Location
- Cincy Ohio
It could work as a theft deterrent too, just sayin...
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
brianp454
Member
- 572
- 11
- 18
- Location
- Portland, OR
Nice!
59apache
Chipmaker
- 1,299
- 29
- 48
- Location
- Bavaria / Germany
Good idea!
To prevent runaways, i would install one of these: http://www.esdvalvellc.com/diesel_valves_aluminum.html
To prevent runaways, i would install one of these: http://www.esdvalvellc.com/diesel_valves_aluminum.html
I agree!
The more 'unconventional' (or less expected) things you can add to shutting down a critical system,
the less likely it would be for the 'bad guys' to succeed in getting away with the MV!
It would at least frustrate them and slow them down.
Katavic918
Active member
- 523
- 54
- 28
- Location
- Maryland
Also a good idea.
Flingarrows
Member
- 138
- 0
- 16
- Location
- N Central Illinois
What type of valve is that Rusty, I need to look into that for my 6bt
Flingarrows
Member
- 138
- 0
- 16
- Location
- N Central Illinois
Did you see any pricing on those?
- 7,409
- 2,503
- 113
- Location
- Interlachen Fl.
But your FDC is not bypassed. Reason?
Jeepsinker
Well-known member
- 5,399
- 456
- 83
- Location
- Dry Creek, Louisiana
I was going to ask the same question. You knew it was going to happen Rusty...
59apache
Chipmaker
- 1,299
- 29
- 48
- Location
- Bavaria / Germany
rustystud
Well-known member
- 9,280
- 2,988
- 113
- Location
- Woodinville, Washington
I actually like the FDC. Mine works great for now, and in the future if it starts to act up I might see if I can fix the sealing problem by a little machine work and adding some 'O'rings.
rustystud
Well-known member
- 9,280
- 2,988
- 113
- Location
- Woodinville, Washington
That's a great valve, but how much does it cost ? I had that "WOG 1/2" NPT Ball Valve" just laying around so it cost me just the one fitting and some time. Most of our runaway engines are caused from the injection pump going "wonky" . That is the official term also.
Last edited:
rustystud
Well-known member
- 9,280
- 2,988
- 113
- Location
- Woodinville, Washington
It's just a standard "WOG 1/2" NPT Ball Valve" I used that larger valve since the hole in the valve is actually 3/8" . I just used bushings to bring it back to size.
59apache
Chipmaker
- 1,299
- 29
- 48
- Location
- Bavaria / Germany
Sorry for hijacking....your idea is good and i also like the keep it cheap and simple way.
I just like the idea with stopping it from the driver seat.
I just like the idea with stopping it from the driver seat.
rustystud
Well-known member
- 9,280
- 2,988
- 113
- Location
- Woodinville, Washington
I had actually bought a Cummins engine fuel shut-off valve, but I didn't want to be dependent on the electrical system to shut down. I do like that butterfly idea though. How much does it cost ?
- 42
- 0
- 8
- Location
- Sacramento/CA
Anyone looking for that valve that rustystud used, can find one at the nearest Home Depot or plumbing supply house. WOG stands for Water, Oil, Gas. Those are important initials when using a valve for this purpose. Full port is also ideal, as then the size of the valve is not smaller than the pipe it is installed in-line with.
bonedoc
New member
- 502
- 1
- 0
- Location
- Bangor, PA
Awesome idea Rusty Stud....on my to do list
HanksDeuce
Well-known member
- 1,081
- 242
- 63
- Location
- Prairieville, LA
I like the K.I.S.S. method.
See my build thread post #291 here for getting rid of the Cummins 6BT shutdown solenoid and using the factory deuce pull cable to shut off the engine.
See my build thread post #301 here for adding a $7 blast gate valve to the inlet of the turbocharger to shutdown a runaway. Cheapest solution I've seen yet.
To shutdown the typical engine you need to get rid of air, fuel, or spark. No spark in a diesel so you're left with air or fuel. Air is the easiest to get rid of. You could shut off the injection pump, but what if your turbocharger inlet seal blows and you start running off your engine oil supply? It always goes back to the air. Pull the cable in the cab and the safety pin pops out. The blast gate shuts. Engine kills. Now it's all fine in theory. I'm not willing to kill all of my intake manifold gaskets to test my theory.
See my build thread post #291 here for getting rid of the Cummins 6BT shutdown solenoid and using the factory deuce pull cable to shut off the engine.
See my build thread post #301 here for adding a $7 blast gate valve to the inlet of the turbocharger to shutdown a runaway. Cheapest solution I've seen yet.
To shutdown the typical engine you need to get rid of air, fuel, or spark. No spark in a diesel so you're left with air or fuel. Air is the easiest to get rid of. You could shut off the injection pump, but what if your turbocharger inlet seal blows and you start running off your engine oil supply? It always goes back to the air. Pull the cable in the cab and the safety pin pops out. The blast gate shuts. Engine kills. Now it's all fine in theory. I'm not willing to kill all of my intake manifold gaskets to test my theory.