Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Started installing a backup camera:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your HMMWV today/lately
- Thread starter Warthog
- Start date
Lawdog734
Active member
- 267
- 101
- 43
- Location
- Colbert, GA
I did the same, but mounted the camera higher, up under the shelf that the Rhino locks into. Putting it there allowed the camera to be more protected and still allowed for an unimpeded view.
- 6,947
- 9,606
- 113
- Location
- Papalote, TX
PIC?
Lawdog734
Active member
- 267
- 101
- 43
- Location
- Colbert, GA
I'm out of town for business travel at the moment, but I'll see if I can't get my son to snag a pic for me.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Hmm, thats not a bad idea. So basically the top bolt of the same bracket? I guess I was worried that the tire would block it. I'll have to try that.
Lawdog734
Active member
- 267
- 101
- 43
- Location
- Colbert, GA
Yup, that's exactly where I put it.
- 497
- 711
- 93
- Location
- Fort Lauderdale, Florida USA
Zombie apocalypse, that's what they called us at my youngest school event trunk or treat.
Attachments
- 740
- 162
- 43
- Location
- Gainesville, Florida
Got the 2-man soft top installed on my M1114 today. Next step, soft doors.
Attachments
- 6,947
- 9,606
- 113
- Location
- Papalote, TX
Check with [B]aghumvee[/B] I purchased some NOS doors from him and I am very happy with the quality and price, there were some small imperfections (small brown spots) in the windows but it is hardly noticeable and of course this was discussed beforehand, He is a good guy!!!
- 740
- 162
- 43
- Location
- Gainesville, Florida
Thanks. I've already got a set. The only problem is that they're camo color.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
I took the advice here and moved the backup camera:
Also finished the install with the monitor and everything. Its hooked up to the TCM power feed wire, so turns on and off with the start switch. It stays on full time when running (I dont want to need to be in reverse to use it).
Also finished the install with the monitor and everything. Its hooked up to the TCM power feed wire, so turns on and off with the start switch. It stays on full time when running (I dont want to need to be in reverse to use it).
- 6,947
- 9,606
- 113
- Location
- Papalote, TX
Is that Motorola mic connected to a Spectra or maybe an XTL?
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Its a Motorola XPR4550, UHF low split so it can do HAM, GMRS, and commercial. Its also hooked up to my intercom system on the receive side. Still need to hook up the intercom for transmit though (hence the mic).
- 6,947
- 9,606
- 113
- Location
- Papalote, TX
Ahhh, you fooled me by slumming with the XTL mic..
Which is likely a better mic anyway, unless you drop it too many times.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Haha, I like the old school micsAhhh, you fooled me by slumming with the XTL mic..
rcamacho
Well-known member
- 772
- 855
- 93
- Location
- Bainbridge Island Wa
Thoroughly cleaned the dashboard to chassis ground. All wire lead corrosion treated with vinegar and scotchbrite. Body panel acid etched.
so far so good with the gauges working normally now.
so far so good with the gauges working normally now.
- 2,976
- 4,360
- 113
- Location
- Olympia/WA
No pictures, but finally got around to repairing my speedometer that stopped working after I shifted the transfer case while the engine was running... (gee, maybe that's why the manual says to turn off the engine first???)
Broke in June, ordered parts in July, and finally repaired it yesterday. All of about 10 minutes, and that's because I kept crawling out from under the truck to look at things.
Wasn't able to remove the broken end of the drive pin out of the gear assembly, probably because I've driven it 500 or so miles while broken like this, so had to spend the extra 5 minutes to swap out the gear as well as the pin.
Broke in June, ordered parts in July, and finally repaired it yesterday. All of about 10 minutes, and that's because I kept crawling out from under the truck to look at things.
Wasn't able to remove the broken end of the drive pin out of the gear assembly, probably because I've driven it 500 or so miles while broken like this, so had to spend the extra 5 minutes to swap out the gear as well as the pin.
- 1,501
- 1,682
- 113
- Location
- Puget Sound, WA
Time to change the oil. It wasn't quite at the mileage point but it isn't raining and the parade is tomorrow, so why not.
- 2,976
- 4,360
- 113
- Location
- Olympia/WA
You doing the Auburn parade?
I have other commitments tomorrow or I would do it.
If you aren't doing anything else Monday, come on down to the Elma Veteran's Day Parade and join that one as well. Even if it's pouring rain we tend to enjoy ourselves (VFW parade entry) More trucks are always welcome.