• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. 86humv

    M1097A2 New Temperature Gauge Not working.

    The sender for the gage is under the alternator.....one wire connection.
  2. 86humv

    Install front winch will not fit with brackets

    Left 12469393-1 Right 12469393-2 I have a right available.
  3. 86humv

    Install front winch will not fit with brackets

    1123 has a winch plate but does not have frame extensions which is needed for a warn electric winch.......Milemarker hydralic takes a whole different setup.
  4. 86humv

    Gap with tire carrier.

    I've seen mud flaps mounted on forward side of bumper leaving a flat surface for Rhino.
  5. 86humv

    prices on 1097a2 vs 1152

    Easier to work on a non-turbo truck......but no A/C usally.....and better gear ratio....1097A2 normally us army and quicker EUC... or 1123, same as 1097A2 but no back bumper, fording parts removed, usmc Euc.
  6. 86humv

    Were non-turbo Humvees produced after introduction of the M11xx-turbos ?

    There are 2003 NA 1097a2's out there
  7. 86humv

    M998 broken spring replacement?

    Thats it.
  8. 86humv

    M998 broken spring replacement?

    I looked at the truck he got from govPlanet....it has cast spring mounts....its in the pics.
  9. 86humv

    M998 broken spring replacement?

    Thats one of the truck like a 1097r1....early truck with later master cylinder, 10k axles, A2 rear bumper and variable rate rear springs....which should be replaced as a pair.....so manual won't reflect properly for a stock 998. Springs you need are: 12342616
  10. 86humv

    M1123 Low Power

    A2 and 11 series trucks have a CAT in exhaust area before short muffler......if all fails, drop the cat out and see if its clogged.
  11. 86humv

    Help with ID of parts

    Mak armor door strykers....junk...not needed.
  12. 86humv

    Glow plug harness question

    The eng. harness has a big center socket that gets corroded ...and its hot all the time with batteries hooked up. I had one once that it was green with corrosion, so I cleaned it out, and then the socket hole was to large to make proper contact with start box.....so I had a doner eng. harness...
  13. 86humv

    Help With Brush Guard Mounting

    Luverne as Steve said...it takes : the one on the right for none winch and left type for winch type bumper.
  14. 86humv

    What Would You Do Here?

    Fuel pump....best time is now.
  15. 86humv

    installing slant back hatch seal

    Aluminum hatch is thicker...so seal has a bigger gap.
  16. 86humv

    How to Prove Date of Manufacture?

    Its an 08.....just pick a month and 2008.
  17. 86humv

    Valve Cover w/ Emission Sticker

    Never heard of a DMV looking at that sticker....and there is different ones depending on if its a GM or GEP engine.....the re-builds from gov plnt mostly don't have a sticker.
  18. 86humv

    Help Identifying Thing On Front Of HMMWV

    So Steve....that means they, or you attached one to your AZZ back in the past....
  19. 86humv

    Help Identifying an electrical component

    Normally if they did as you say....the EESS control box under dash is toast.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks