Search results

Here is a shot of the cable ends. Google Image Result for http://www.tpub.com/content/misc_manuals_1/TM-11-5995-208-10/TM-11-5995-208-100008im.jpg

No it's def, comm wire, I believe this is what it might hook into. Part B. Cable Assembly CX-11230( )/G

This roll of wire was on my Mep002A. Found out it is for communications. 1/4mile of wire, with ends in tact. Wondering if there is a use or is it salvage (sems a shame to salvage). Thanks bob.

Look here for receiver plate that will allow plenty of height adjustment, mine works great. Bob. http://www.easternmarine.com/Pintle-Hook-Adapter-Mount-PM1012/

I'm without a doubt changing the cord, that was my original question on cord size and length, would like to go 100'. I got a PM on Ronk transfer switches, would like to keep everything outside, that is why I have a 200amp exterior entrance box. Next questions will be proper way to hook to the...

The set up was put together to get me going during a extended power outage, I understand the risk of shock and would not fire the generator until the plug was installed. The lock out is inside the disconect pannel, mechanical device between the 30amp breaker and 200 amp service breaker, gen...

Hey gus I have the interlock switch installed on my sub pannel box (200amp), I agree that is the bare minimum, hopefully someday I can get the transfer switch, keep waiting for a sale. What do you guys think about diirect connect to the Lugs w/sjt cord, or go with a disconnect and outlet?:roll:

Ok here are pics of what I'm using w/ package store genset, it is an L14 twist i put on it and same with outlet installed. Suggestions on hooking to Mep002a; If i want to go 100' what type cable is the best and were to get it. Assume I should wire dirrect to lugs, will the 30amp outlet I have be...

What are the suggestions for Cable size and configuration to come off the lugs on my Mep002a. My store bought Gen set has 220volt twist lock that goes to outlet, then through transfer switch (sorta home made but does work well). Any experince would be appreciated. Thanks Bob.

Here is the link for the CAMO Pattern M101A2 Figure 122. Trailer, cargo: 3/4-ton, 2-wheel, M101A1. (1 of 2)

I agree with RAPCO, Just did my M101A2, great coverage, easy to use, also you can get the pattern from the TM as well. Bob.

WalMart in Carlisle is were I got mine and they had 4-more on 10/09/10 and they were dated 9/10, pretty fresh. Make sure you take the fuel tank off and soak & clean, soak and clean, then purge your fuel lines, leave the drain open on the strainer for a few seconds. Also my starter was froze up...

TM and plate on Mep002a says disconect Negative first, Reconect Positive first (it states to hook the +- jumper first). I also get a small arc. Bob.

Ok. Went out this AM and tightend all the screws in the CB, some were loose, Started her up and Hertz meter is working 1/4-1/2 throtle right on 60 htz, will PU Kill- A watt, were is a good place to purchase one. Thanks Bob.

Ok, with throttle back she still is pegged all the way to 65+++, My VM does not have hertz, will get one, should I be reading on the Lugs, I get 120 on outlet.

All 3- Meter's not functioning. Frequency meter goes to 65 hertz and stays there, shut it down and it goes to 55. % rated current meter, bounces to about 60 then back to 0, Voltmeter runs up to 110 max then back to 100. Outlet reads 120 all the time, if I move the voltage adjust it does move...

I was reading the TM and found this!! SHUTTING DOWN UNIT. Place AC circuit breaker in the OFF position. To stop the Generator Set, place the master switch in the OFF position. c. After operation of the Generator Set, perform the inspection and service requirements as outlined in preventive...

THANKS, for all the help before, during and after. Followed all the advise, battery 51-R WalMart 62.00 ea., Fuel Filter Fram C1125PL Race Mart 5.95ea + shipping, Fram Oil Filter CH6PL 6.00 Tractor Supply, Air Filter Napa #2222 28.50. Took everything apart, cleaned, purged and started 3rd try...

Proud new owner of Mep002a w/ Trailer and cover, just PU and draged home from Fort Meade, getting close to firing her up.

WOW, I finally took the time to slow up and look, You're correct, So now I have 1300' of RC cable!!!!!!!! Nice stuff, no use that I can see. [thumbzup]