Search results

I'M NOT THE FUGLY GUY IN THE MIDDLE !!! This is what I get for picking on peoples garage treasures huh? That's it. Alternator prices just doubled...

Fellow SS member Wildchild467 made the news with the appearance of his M35a2 at the Woodward Dream Cruise 2016. His girlfriend is the one with the hat on:

0.875" is standard heavy duty 7/8" alternator shaft diameter. Numerous different ones easily available with various belt types, offset, diameter, etc.... There is a balancing act on higher output alternators, because you want them to spin fast to charge at idle, yet with a smaller alternator...

Cute. As good as yours is now: Starter: Mitsubishi Electric 24V 7.5kW, 105mm, gear reduction, 29lbs, mfd 2016 https://www.diamond-gard.com/application-guides Alternator: Delco Remy 28Si, 110A, 24V, model 8600467, twin fan, mfd 2016 (benchmarking)...

TM says owner/operator.....

Thanks. Woodward Avenue in August, slightly North of Detroit. Woodward is the first paved mile of road in the US. This event now draws the largest number of automobiles annually of any single event in the world. Over 40,000 vehicles and +1.5 million spectators.

Made a news pic of Woodward Dream Cruise from August 16'. Hopefully see some of you there this year if you attend.

Hats off to somebody doing that much cab work, but I do like the look of post #11 as a favorite. Back seat without 4 door, all of it, perfect.

^This^. You may have something going on with your steering gear, causing the pump to pressurize the fluid continuously rather than as needed. This will over-temp the fluid, causing the fluid to expand, soft hoses to burst, etc.... Should not really have to bleed a pressurized recirculating...

That relay is fine. Best wishes to the OP, polite of everybody else to stay along and help. Welded starter solenoid contacts can and do happen.

That is a lawn mower relay. OK to use if not carrying more than starter solenoid current.

I bought a thick aluminum plate to put atop of my 925a2 hard top to support my cab roof air conditioning unit (Red Dot R-9777). Not installed yet, but hope to this spring. Same concept you are thinking though, a way to create a hard top surface that can bear some weight. As of stock, they are...

The key slot is just there to confuse you. It is not used. Taper fit to gear. Your thinking is correct, pull gear, back up 8 degrees, re-install, should give you 16 degrees. Can confirm with spill port timing method, easy to do.

99, you're really in a hurry to put something other than motor oil in your engine? What does it look like under the fill cap? I only did the ATF trick to silence lifters that had morning sickness, not on a regular basis. If your engine is not sludged, just change the oil.

azkcr, video your attempt at that and post a YouTube link. Make sure your wife says lot's of OMG's and the family dog is running around barking in it.

Please keep me in if you guys do make a visor, I really like the look also and want one for my 925a2. I've only seen one guy do it so far, and that was a complete cab swap with semi truck doors, all that. Looked beautiful. I'd be lucky just to get the visor.

As thought. Cool. You'll need to drain coolant down to below stat level, so that is at least half of it or more. At that point, drain all, do a Cascade flush, change stat, and refill with new. Good for another 5 years or whatever.

Cool stack !!! Beard of chains isn't too shabby either. I enjoy to see creative ideas. Is your fan spinning when engine temp is say 100F? If not, then it is correct and you'll need a new thermostat. Shutter should not be leaking, take it apart, clean, and lubricate it, try again. So it...

I think it has a bunch of bad reviews, all over. So much to the point it is difficult to find in stock anymore? My experience is that it caused a small 4 cylinder of mine to suddenly have a lot of blow by, broken rings, etc....immediately after using it. Also, the can specifically states...