Search results

I have this problem on my 813 (1400x20's). The motion is a resonance. It is being stored/released in spring or tire in frt/behind. The latter is causing the pair to bounce like a teeter totter. It is always 30mph +/- 5mph. 1 tire on each side (rear) has 1/4" radial run-out. Adding max air (95)...

Below is something I found online (I can't remember where). May be of interest here. -----Original Message----- From: Powermaster@cummins.com [mailto:Powermaster@cummins.com] Sent: Tuesday, August 19, 2003 2:03 PM To: xxxxxxxxxxxxx.com Subject: Re: RQST00000169662 - NHC 250 engine manual...

Nice

It was not my intention to offend you. I was just trying to clarify.

#9 Myth: The United States lost the war in Vietnam . Fact: The American military was not defeated in Vietnam . The American military did not lose a battle of any consequence. From a military standpoint, it was almost an unprecedented performance. General Westmoreland quoting Douglas Pike, a...

I missed the Jacobs engine brake. It will not fit without some mods.

I'd leave the pipe and manifold uninsulated. You peak under hood air temp is 100+*F cooler than the intake charge at 15 psi. Big rigs that I used to drive never had insulation on either the intake or exhaust. Under hood air may be radiator warm but it is moving very fast. Cold by exhaust system...

I'll bet that thing fits. It will be interesting to see how much boost you have. The intercooler isn't even close to 100% efficient and the water is already 180. Unless you are at or above say 20-25psi it may do little towards cooling the charge. What I am seeing is low EGT and figure that even...

M-105 w/narrowed 5000lb mobile home axle. F rated 14.5 tires. The old stamped steel wheels are rather hard to find now. Square tube tongue. tilts.. Had some U bolts made at local spring shop. Had to fiddles w/ spring pads on the axle tube. A few leafs were removed too, but still takes 4000lbs cargo.

It will if you put a bar thru the large hole. Were they issued with 2 handles? I made a single double duty bar out of 3' long round stock (for large hole). I turned down one end a for a few inches so it does the small hole too.

2011 Baldwinsville, NY M35A2 passenger - John J. LaFrance (Tonawanda, NY) served w/82nd Airborne WWII (POW Bastonge)

It will when the water is frozen.

False. If that were so they would have put a warning on the dash, or something in the TM....

I added the 'D' to my black smoker, stock, LD and it made some silly HP. I turning down the IP 2-1/2 turns and it is still a very strong, reliable, runner. I'd guess 40-50%. Very noticeable change and quite a contrast from the stone it once was. I'm sure 90 HP is possible. Use W/A injection...

11 new 1100x20's, painted inside of box, d-seat side rifle mount

A lot of foreign countries bought them. Here are some retired hulls in Sudan. I can't remember who sent me these. (possibly M813RC or Hellonwheels?). Maybe they were posted here.. Maybe thee guy in the picture can chime in... 3 Alvis Saladins can be seen in background. Last year(?) I...

It's hard to appreciate the size of the 8" projectile in the video. The M106 shell weighs 200lbs and stands about 35" tall. The clip shows 4 guys handling it. They have a raised carrier to get it up to the breach (head height). 5000? I'm beat after moving one across the room.

http://www.steelsoldiers.com/cadillac-gage-v100/40838-need-info-about-v100-wheels-help.html

...

From the 5 ton lubrication order(LO 9-2320-260=12 March 1979, page 28, note 6, emphasis added). M35 is similar. Change gear lubricant only when required by maintenance repair action, or if contaminated by water or other foreign material. Drain only after operation when hot. Place vehicle in...