Search results

Finally getting around to teardown and wire replacement... Looking at replacement terminals and wire now. Terminals are6 awg 1/2” and 1/4” ring nylon crimp. Wire is 6 awg milspec high temp M5086/2-6-9. Teminals are easy enough. Wire is nearly unobtanium and Very expensive. Abrasion...

I saw an 1123 on Govplanet that had obviously been rolled. The entire A pillar structure folded rearward along with the B pillar. Sent from my iPhone using Tapatalk

If you are planning on highway driving the 4 speed transmission is more humane. Slightly less risk of getting rear ended if you can keep pace with the speed limit. Sent from my iPhone using Tapatalk

Addendum, I tightened all three canister top cover bolts and fuel fittings. No leaks now. [emoji106] Sent from my iPhone using Tapatalk

Wow, that makes my nearly plugged filter look pristine! Surprised it ran at all... Sent from my iPhone using Tapatalk

Followed procedure per unit maintenance TM Section 3-33. O ring was installed correctly and not pinched TMK during installation. The housing is definitely seeping past the ring upon inspection today. It did not leak previously. Bummer, gather I’ll have to repeat the service. Sent from my...

Fuel filter. [emoji106] Fine filter screen was good. Truck picked up a bit of power post filter change. I gather flow to the IP was restricted. Original filter looks to have a minor mfg defect vulcanizing the metal screen to the end cap. Sent from my iPhone using Tapatalk

Horn circuit preferred? If not, where? Sent from my iPhone using Tapatalk

Finished reverse light installation. Tractor switch in 3 speed shifter reverse location. Clearance is tight inserting shifter in body with oversize switch. It may take some finesse. Took the opportunity to aluminum nutsert the gearshift bolt holes. Prestolite wiring and packard connectors...

Switched over to hardtop style windshield brackets. I prefer the better angle for the Xdoors. Moved the Plan B top forward a tad to accommodate the change in fitment. 12338833 5340-01-247-7812 Sent from my iPhone using Tapatalk

Varitread. Expensive though Sent from my iPhone using Tapatalk

Added missing rear shackle mounts on A0 airlift. Now I need to find reasonably priced shackles [emoji1751] Sent from my iPhone using Tapatalk

I have original X doors on an M998. Currently well aligned to the striker pin and operating well. Looking to adjust the door to sill and B pillar gap as a few doors are misaligned. What’s the fitment guidance for gap to sill and B pillar? Eg 1/4”-1/8” etc? Sent from my iPhone using Tapatalk

Congratulations! I’ve also been looking at the 1165A1 REV stock and am seriously considering one as well Sent from my iPhone using Tapatalk

Finished installing LT inside cowl insulation. It’s a bear of a job unless the tub is off the frame but it can be done. TM is a good reference and fairly complete. Note insulation piece must be cut in two along parting line per TM for retrofit or replacement on vehicle. Sent from my...

I’m using the plow springs front and rear on the 998. It sits about level unloaded. Sent from my iPhone using Tapatalk

Old thread reactivation I know. Parts TM was a great reference when looking at replacement rear springs for my M998. My vehicle had sagged springs RF and RR. To my surprise the 12338316-2 spring is used in the rear for the M998 H13 UOC. Same spring is used in the Hummer H1 snow plow...

28-28.5 nominal range? I’ll be leaving it as is due to the seized plug. Sent from my iPhone using Tapatalk

Pipe plugs suck. I measured alternator output voltage today 28V. The adjuster plug is frozen in place. Nice procedural video btw: Sent from my iPhone using Tapatalk

Lift pump tested good for cold cranking flow [emoji106] Sent from my iPhone using Tapatalk