Search results

I can probably twist my biddies arm to look after the 'scope for you. He has a load of stuff here at mine ready to go the other way.

If JATONKA isn't coming to the rally - I can stop by his and pick stuff up... (JT - let me know if you are going)

Thanks for doing the vid Brian. I'm still a long ways from putting my 816 on the road and doing my own vid!!! I can bring these to GA rally if people PM me up front. No payment necessary till rally.

I have one ground spade for an 818 tractor or M543/M816/M936 wreckers...... $80

You are correct, tandem winches are used for loading disabled tracked vehicles. Just like the HET and right back to the M26 Pacific in WWII. They can be stacked or side by side. Question is - how are the winches set up re drive/freewheel/brake etc., on the ones you are looking at. Probably you...

Welcome from further upstate (past Cooperstown). Speaking of antique trucks/transport etc., I have a Pete 352 (12v71) that needs to get to Port of Baltimore before first frost... Looking for shipping quotes. Howard

HEMTT stinger parts wanted Anyone have any of these parts for a M984E1 stinger? Jeff ~ you implied you had seen these being replaced/repaired maybe?

Parts Wanted - M809 Series 5 ton. Battery box - either plastic or steel will do. Fuel tank - (drivers side)

Great to have a wrecker / crane safety operation posting every once in awhile... Two points; - Esmet fittings have a small hole in them so that upon reassembly, you can see that you have set the end of the cable in far enough before tightening the nut. - Those "wedge" type fittings that have...

Glazing putty won't go completely hard and it's oil based. Why do you say no bondo when gone to bare metal? If you need to fill ie., don't want to see effects of rust, the only real answer is to 1 remove scale, 2 treat rust (Ospho etc.) [or blast to cover both steps 1 & 2], 3 fill (bondo), 4...

Not sure if member who has you stuff is coming to rally? Here's a new thread for shipping to/from rally. Can you assist or need anything brought back.... Use PMs for details/phone numbers etc., except big Jeff - PM box often full ; ) TO RALLY:- State - ( currently at SS member, location )...

I have some parts that need to be brought to rally - was wondering if there is any mileage in starting a new thread (don't want to get posting lost in "date change" thread, or this "buy-sell-trade" thread as it's not really appropriate) just for S/S underground railroad/shipping - to/from rally...

Hi Steve and welcome. What was your trade? Assuming you are ex REME... Land Rovers on this forum are a bit of a rarity, couple of 1 tonnes and a few lightweights. As soon as you are able, how about some pics? Howard (expat - Braintree, Essex.)

If either of you want these before the rally - to try out driving there(??..!), I can post them pretty cheaply - they're not heavy, I'm shipping one later today. Gimp - Yes Moneypenny, that's the plan, shaken not stirred, though I'll be in a different vehicle!

........ and probably better than they were ever done in the military (??). I thought over/under spray was more authentic, especially in a combat theatre? Unless of course they were done freehand with a brush. Clarification required.

M816 rear winch "Roller ponding" - Fix Had forgotten to post these from some time ago. My solution was to extend the grease fitting then caulk the void: I/Fittings. II/Fittings installed in roller. III/Roller test fit in frame. IV/Cap in place. V/Masked nipple for painting (Nipple will be...

Been discussed before : http://www.steelsoldiers.com/showthread.php?97456-M816-rear-winch-roller-drain&highlight=Roller+Ponding ... but I had forgotten to update the thread.

Not for crane use (must use shackle for that), but for recovery use, choker hold can be used if you shove a load of grass or a couple of sticks in the choke. These will compress but will also swell back a bit and can be pulled out piece meal. Also softer "upside the head" if sling gives way!

Found your door decal: ... of course you don't need the barrel organ.

Minor update - A local highway dept has just acquired an A3 from Germany (??) and will be pulling the winch/fifth wheel to make a plough truck. Anyway - I got a good look at the winch tower/remote lines and found that the High/Low speed valve as on the A1/A2's has a third 'Aux' position which...