-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Buzzards Roost
- Thread starter Rhino 5/4
- Start date
Good morning everyone. We finally got off high center and back to moving forward on the Roost. The deuce and 5 ton wheels were all broken down and deuce wheels and rings sandblasted, wire brushed, primed and painted. we had to repaint when mounted on truck, I tried to rattle can the hubs, studs and nuts but the can did not match the spray gun for some reason, maybe the thinner we used and ratio. working on getting the roof back on her now but will be doing a run and on vacation wiht the boys for the next couple of weeks so not much progress will be made. 
- 7,716
- 19,766
- 113
- Location
- Charlotte NC
.
Lookin Good!
I know it would seem ok to me and u and Third as well to take the kids with you on vacation to Vegas cause its never too soon to teach them how to count cards and how to take the hinges off the in room mini bars and other highly sought after skills !
Last edited:
- 16,755
- 24,064
- 113
- Location
- Burgkunstadt, Germany
Chucky's back in town!
Roof done for now. Haven't water tested yet. Windows came in last week. Last shoot this weekend and hopefully will get some faster progress soon. Pulled seats from red truck and had radiator cleaned hoping to solve overheating issue. Planning on raptor line whole truck sand color with black body lines. Roof didn't turn out quite like I wanted but should be good to go after sealing with raptor line. Hopefully get on road to test drive this week. Looking for a good hard top if anyone knows of one. I might have to reskin the top of one of the ones I have or swap over the red top for time being. Been busy with work and doing 4 shoots this month. 
dr3d
Member
- 30
- 61
- 18
- Location
- Gulf Coast, Texas
LMBO ... finally scrolled from the top. Good news 'cause I ain't no more worried about offending the crowd. I talk fancy sometimes, but you'll get over it.
So, is this rig named after a water'n hole just our side of the border? If it is, we share some friends.
With that new roof I ain't gonna have any luck talking you outa that 109 box. I am sure hoping to stumble across one before I build a replica. Bring'n home a '71 in a couple weeks and a 109 box would be one heck of a short cut.
Well played brothers.
Sent from my SM-S908U using Tapatalk
So, is this rig named after a water'n hole just our side of the border? If it is, we share some friends.
With that new roof I ain't gonna have any luck talking you outa that 109 box. I am sure hoping to stumble across one before I build a replica. Bring'n home a '71 in a couple weeks and a 109 box would be one heck of a short cut.
Well played brothers.
Sent from my SM-S908U using Tapatalk
Glad to meet you dr3d Sir. Actually one of my uncles had the blacklight poster (my avitar) from back in the day and my grandfather found it and put it in his bathroom when he built it. He was my hunting buddy and he said it reminded him of me, (I have a sitting still problem) hehehe. I got the poster when he passed and hoping to restore it best I can and put it in the Roost. They just seem to go together I guess. There were several 109s where I got mine but havent been back in a long while so I do not know if they are still there. I will check next time I am that way. Not too far from Waco in Gatesville. They were all in rough shape but certainly repairable I would think. You might consider the reproduction as a better alternative. rebuilding this ol girl has been a lot of work and still have a long way to go. I was thinking about getting a cargo trailer built less the tongue and axle and setting it on the red deuce I have to see how it would work out. Hope to meet you in person, my grandsons live in Shiner and my granddaughter in Bastrop so I will be certainly going that way with her in the future. Oh, and Ya, feelings, i dont do and if the truth offends someone, well..... you might need to go check yourself.
Attachments
Those corners turned out good ! You might have roofers blood in ya after all !
Ty. Wish I was with the. When they cut them out. But it is what it is. As long as it doesn't leak I'm good with it.
A little more headway this weekend, I found a big spreader bar and we have a big skytrack at our work, I am seriously considering lifting the box off so I can paint between the cab and box. I think I counted 8 bolts or so on each side. might not be too big of an ordeal. Brakes are still an issue, Bled, adjusted, re bled still slow to stop with pedal all the way down. Going to go through rear wheel cylinders next, i just installed front wheel cylinders and airpack with master cylinder recently. Discovered the selector shaft on the winch is broken, would anyone know of a source for one and how much of a pain it will be to replace?
Still in search of a good hard top if anyone knows of one for sale. Shooting for 9-19 to make her first Run n Gun trip.
Still in search of a good hard top if anyone knows of one for sale. Shooting for 9-19 to make her first Run n Gun trip.
Attachments
Progress report 10-17:
Overheating issue resolved, Drove 200 mile round trip last weekend ( Sunday afternoon was pusing 100 ambient) no issues.
Tstat was broken in open position and replaced,
Replaced the radiator with the one that was on the red deuce, it was NOS and had been replaced recently it looks like.
Waterjacket was really rusty, poured 7 gal of evapo rust in cooling system and ran it for a couple of days, flushed and re flused several times now have clean system.
Swapped all the fuel filters with the spin on ones that were on the red deuce and put new filters on both trucks.
Winch and bumper cleaned, painted and installed except for drive and PTO. I will have to pull winch this winter and rebuild, selector shaft is broken off in the case.
G177s are the best, I bought 3 from Fuzzy and put 2 on the trailer to even it out and mounted a hoist in the back of the trailer to lift the spare in and out.
a couple of gauges replaced.
4 camera system installed.
backup light installed.
Found some Mammoth Tusk I think I am going to put on the 1911. I was going to re scale a fixed blade but looks pretty sweet on big girl. Not related but I guess it is if its a EDC hehe.
Repaired the best Jpipe I had, I found some prebent 90's to fix the other 2 trucks. all of them were rusted out at the bottom.
I found a COP Box and used it for the bed base and test fitting some tool chests to see how the floor plan will work out.
I still have a couple of roof leaks I need to address soon and I think my fuel tank pump is not working or if it is it is intermittent.
Mike V. is looking to see if he has a heater unit for me so I can be a little warmish for this winters adventures.
Still looking for a good cab if anyone knows of one in the Texas area.
Sorry for the lack of communication, it has been a busy few months.
Overheating issue resolved, Drove 200 mile round trip last weekend ( Sunday afternoon was pusing 100 ambient) no issues.
Tstat was broken in open position and replaced,
Replaced the radiator with the one that was on the red deuce, it was NOS and had been replaced recently it looks like.
Waterjacket was really rusty, poured 7 gal of evapo rust in cooling system and ran it for a couple of days, flushed and re flused several times now have clean system.
Swapped all the fuel filters with the spin on ones that were on the red deuce and put new filters on both trucks.
Winch and bumper cleaned, painted and installed except for drive and PTO. I will have to pull winch this winter and rebuild, selector shaft is broken off in the case.
G177s are the best, I bought 3 from Fuzzy and put 2 on the trailer to even it out and mounted a hoist in the back of the trailer to lift the spare in and out.
a couple of gauges replaced.
4 camera system installed.
backup light installed.
Found some Mammoth Tusk I think I am going to put on the 1911. I was going to re scale a fixed blade but looks pretty sweet on big girl. Not related but I guess it is if its a EDC hehe.
Repaired the best Jpipe I had, I found some prebent 90's to fix the other 2 trucks. all of them were rusted out at the bottom.
I found a COP Box and used it for the bed base and test fitting some tool chests to see how the floor plan will work out.
I still have a couple of roof leaks I need to address soon and I think my fuel tank pump is not working or if it is it is intermittent.
Mike V. is looking to see if he has a heater unit for me so I can be a little warmish for this winters adventures.
Still looking for a good cab if anyone knows of one in the Texas area.
Sorry for the lack of communication, it has been a busy few months.
Attachments
dr3d
Member
- 30
- 61
- 18
- Location
- Gulf Coast, Texas
So ... 'bout that 1911; sure looked familiar. One heartbeat of where the flip is my BBR (carrying otherwise today) before I realized that ain't mine.
It's the 507 on a compact that twisted up the heartbeat.
Sent from my SM-S908U using Tapatalk
It's the 507 on a compact that twisted up the heartbeat.
Sent from my SM-S908U using Tapatalk
Ya sent it off to get milled and a tune-up. Very happy with it. Red dots are the best for old tired eyes hehe
Man u been gettin it done ! Way cool rifle drawer !
Thanks @chucky
I am just fillling holes to see how everything will finally end up and use stuff that is readily available and repurpose stuff and utilize every sq inch I can wisely. I think I will put a grinder toilet beside the sink with a curtain around it and use an outdoor shower instead of indoor. Something kinda like the picture, I saw where you can get inserts ti plumb it in the wall and have access to the valves and wand.
I am just fillling holes to see how everything will finally end up and use stuff that is readily available and repurpose stuff and utilize every sq inch I can wisely. I think I will put a grinder toilet beside the sink with a curtain around it and use an outdoor shower instead of indoor. Something kinda like the picture, I saw where you can get inserts ti plumb it in the wall and have access to the valves and wand.
Attachments
Macerator toilets are pricey and i had them on busses for 30 yrs and they are not all that ! They will grind turds and bio toilet paper most of the time but will not grind dead red rats if you know what i mean ! I made alot of money getting them out lol ! That once dumped on the accountants desk they gladly paid but moral of the story you can just put a plastic trash bag in the toilet for have to cases and use other bathrooms for solids 99 percent of the time use THETFORD holding tank treatment u wont smell anything ! Rule no.1 you never can have enough storage ! Line every wall top to bottom with light weight cabinets
Drove the ol girl on a 500 mi round trip to a team shoot last weekend. 8.5 hard miles with 9 shooting stages. We got 13th out of 56 teams. Dog bone came off on front side and plowed into the ground, luckily I was driving into the camp. Did a field repair and walked her home. She ran very good with no issues except for the almost crap show.
Attachments
- 74
- 107
- 33
- Location
- San Angelo, TX
Where was the team shoot?